MACKISSIC SC300M - User Manual

37 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

OWNER’S MANUAL

SC300M

SHREDDER-CHIPPER

ASSEMBLY AND OPERATING INSTRUCTIONS

.

This manual contains information concerning proper and improper operating procedures, warnings,

maintenance, trouble shooting, assembly, tips. Everyone who operates this machine should read

these instructions and be thoroughly familiar with them.

THIS MACHINE IS CAPABLE OF INFLICTING

SERIOUS INJURY IF OPERATED IMPROPERLY

- READ WARNINGS AND CAUTION LABELS -

MACKISSIC, INC. P.O. BOX 111, PARKER FORD, PA 19457-0111

PHONE: 1-800-348-1117 e-mail: info@mackissic.com Fax: (610) 495-5951

3/2018

Table of Contents

Questions and Answers

S
Sandra MccormickAug 4, 2025
Why does my MACKISSIC SC300M Chippers/Shredders engine smoke?
- P
  Paul LewisAug 4, 2025
  If your MACKISSIC Chippers/Shredders engine is smoking, check the oil level and adjust if needed. Ensure the machine is level, as operating on too great an incline can cause smoking. The air filter might be dirty, so replace it. Also, you might be using the wrong type of oil for the temperature; consult your engine manual for details. Make sure the cooling fins are clean and free of debris.
E
Emily EscobarAug 14, 2025
What to do if my MACKISSIC SC300M engine lacks power?
- Y
  Yvonne MendozaAug 14, 2025
  If your MACKISSIC Chippers/Shredders engine lacks power or isn't running smoothly, ensure the choke lever is fully to the RUN position (left) and the throttle lever is fully to the right (FAST). A dirty air filter can cause this, so replace it. A dirty or cracked spark plug may also be the culprit. If it's oily, remove it, cover the plug hole with a rag, pull the recoil cord to clear oil from the cylinder, then clean and reinsert the plug. Old gas or dirty engine oil may also be the issue, so replace them if necessary. Use a fuel stabilizer if you store gas for more than a month. Finally, check that the cooling fins are clean and free of debris.
T
Todd GarciaAug 25, 2025
How to fix a recoil that is hard to pull on MACKISSIC SC300M?
- M
  Matthew SmithAug 25, 2025
  If the recoil on your MACKISSIC Chippers/Shredders is hard to pull, start by removing any debris from the Shredder/Chipper Hopper Inlet(s) and Discharge Chute. An oil compression lock in the cylinder might be the cause. Remove the spark plug, cover the spark plug hole with a rag, and pull the recoil cord several times to clear any oil from the cylinder. Clean and reinstall the spark plug. Check the engine oil level. The engine may be seized or the recoil itself may be broken or jammed.

Summary

General Safety Rules

Safety Labels and Information

Details safety and information labels found on the equipment and their importance.

Personal and Bystander Safety

Provides guidance on protecting yourself, others, children, and pets during operation.

Safe Operation and Precautions

Outlines essential safety precautions for operating the shredder-chipper correctly.

Setup and Engine Start-up

Controls and Features Overview

Identifies key controls, features, and outlines the unpacking process.

Unpacking the Shredder-Chipper

Step-by-step guide for safely removing the machine from its packaging.

Engine Preparation and Start-Up

Covers engine preparation, start-up procedures, and initial operational checks.

Operation and Material Processing

Safe Operation Practices

Details essential safety practices to follow during machine operation.

Material Processing Guidelines

Provides guidance on suitable materials and processing techniques.

Using the Chipper and Shredder Hoppers

Instructions for feeding materials into the chipper and shredder hoppers.

Handling Jams and Clogs

Procedures for safely freeing jammed rotors and clearing clogged components.

Maintenance Procedures

Regular Maintenance Checklist

Details the regular maintenance checklist and required service intervals.

Lubrication and Belt Tension

Explains lubrication of fittings and checking drive belt tension.

Belt Alignment and Replacement

Covers procedures for aligning and replacing the drive belt.

Knife and Hammer Maintenance

Guides on knife sharpening, rotor hammer maintenance, and replacement.

Clutch Service

Details on removing and replacing the machine's clutch assembly.

Troubleshooting

Common Issues and Solutions

Lists common operational problems and provides step-by-step solutions.

Parts Lists and Schematics

Basic Machine Assembly Details

Lists parts and provides schematics for the basic machine assembly.

Component Assemblies Overview

Includes parts lists and schematics for various component assemblies.

Hoppers and Screen Details

Lists parts and provides schematics for the hoppers and screen.

Rotor Assembly Details

Lists parts and provides schematics for the rotor assembly.

Daily Checks and Storage

Daily Operation Checklist

Provides a daily checklist to ensure optimal performance and safety.

End of Season and Storage

Instructions for proper storage, including seasonal and long-term preservation.

Limited Warranty Information

MACKISSIC SC300M Specifications

General

Brand	MACKISSIC
Model	SC300M
Category	Chippers/Shredders
Language	English

Related product manuals

MACKISSIC 12PTE