Magnadyne MKE-300A User Manual

Installation Manual
Keypad Keyless
Entry System
Models:
MKE-300A and MKE-400A
For Technical Assistance call (800) 638-3600 or visit www.magnadyne.com
Locks All Doors
(Including Cargo)
Locks All Doors
(Including Cargo)
Press Simultaneously to
Turn On / Off Porch Light
Locks All
Cargo Doors
Unlocks All
Cargo Doors
Unlocks Entry
Doors
Turns On / Off Porch Light
(Can be Programmed to
Unlock Cargo Doors)
Unlocks Entry
Doors
Unlocks Cargo Doors
(Can be Programmed to
Turn On / Off Porch Light)
Transmitters
2
Programming
A. 3-Button Transmitter Programming
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter memory
is exceeded, the security system will start deleting
transmitters from memory in chronological order.
1. Turn the ignition switch to the "ON" position.
2. Within 15 seconds, push the Program Button
(located on the back of the housing) 3 times. The
onboard LED will be flashing and the beeper will
emit a long chirp to indicate the system is in
Transmitter Programming Mode.
3. Press and hold any button on the transmitter
until the onboard LED turns on for 2 seconds and
the beeper responds with a confirming chirp, indi-
cating the signal has been stored into memory.
4. If you have additional transmitters (up to 4)
that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn the ignition switch to the "OFF" posi-
tion, or wait for 15 seconds. The onboard LED
turns off and the beeper will emit 3 long chirps to
confirm exit.
B. 4-Button Transmitter Programming
Note: This mode will only retain the last 4 remote
transmitters programmed. If the transmitter memory
is exceeded, the security system will start deleting
transmitters from memory in chronological order.
1. Turn the ignition switch to the "ON" position.
2. Within 15 seconds, push the Program Button
(located on the back of the housing) 5 times, the
onboard LED will be flashing and the beeper will
emit a long chirp to indicate the system is in
Transmitter Programming Mode.
3. Press and hold any button on the transmitter
until the onboard LED turns on for 2 seconds and
the beeper responds with a confirming chirp,
indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4)
that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn the ignition switch to the "OFF" posi-
tion, or leave it for 15 seconds. The onboard LED
turns off and the beeper will emit 3 long chirps to
confirm exit.
C. Feature Programming
1. Turn the ignition switch "ON" then "OFF".
2. Within 15 seconds, push the Program Button
(located on the back of the housing) 7 times, the
onboard LED will be constantly on and the beeper
will emit a long chirp to indicate the system is in
Feature Programming Mode.
3. Press and release the transmitter button or
keypad button that corresponds to the feature
you want to change (see chart). The beeper
chirps and the onboard LED flashing will indicate
setting.
4. Continue to press and release the transmitter
button or keypad button until the beep response
matches your desired setting.

Magnadyne MKE-300A Specifications

General

Brand	Magnadyne
Model	MKE-300A
Category	Remote Starter
Language	English

Summary

Installation Manual

Keypad Keyless Entry System

Details the models MKE-300A and MKE-400A for the keypad keyless entry system.

Transmitters

Transmitter Diagrams

Illustrates the functions of buttons on 3-button and 4-button transmitters.

Programming

3-Button Transmitter Programming

Procedure for programming 3-button transmitters, retaining the last 4 remotes programmed.

4-Button Transmitter Programming

Procedure for programming 4-button transmitters, retaining the last 4 remotes programmed.

Feature Programming

Procedure to enter feature programming mode to change system settings via transmitter or keypad.

Operation

4-Button Transmitter Operation

Details the functions of each button on the 4-button transmitter and their corresponding system outputs.

3-Button Transmitter Operation

Details the functions of each button on the 3-button transmitter and their corresponding system outputs.

System Programming

Reprogramming All Codes to Default

Procedure to reset all system codes back to their factory default settings.

Changing the Program Code

Instructions for changing the system's program code from the default or current code.

Programming User Codes

Procedure for programming or changing user access codes, retaining up to 4 codes.

Keypad Operation

Keypad Functions

Details operations like locking/unlocking doors, controlling cargo doors, and porch lights via keypad.

Channel Outputs

Explains activation of channel 3, 4, and 5 outputs via keypad input.

Beep Feature Control

Instructions on how to turn the keypad beep feature on or off.

Wire Descriptions

Pin Position Wire Assignments

Lists and describes the function of each wire in the system's harness based on pin position.

Wire Harness Notes

Provides notes on specific wire harness connections and optional relay pack usage.