Mahindra SCORPIO 2014

Questions and Answers

D
David JacobsAug 18, 2025
What to do if there is no communication from EMS in Mahindra SCORPIO 2014 Automobile?
- J
  Jonathan MartinezAug 19, 2025
  If there is no communication from the EMS, it could be due to a disturbance in the CAN wiring, such as a short to +/- or a terminating resistor issue. Check the wiring and rectify any problems. Another potential cause is that the EMS is not getting an IGN input, or the EMS is defective. In this case, check the wiring and rectify any issues, or replace the EMS.
J
justincastanedaAug 21, 2025
What to do if the signal from EMS is not received by ICU in Mahindra SCORPIO 2014 Automobile?
- W
  williamhodgesAug 21, 2025
  If the ICU is not receiving a signal from the EMS, the issue could stem from a disturbance in the CAN wiring, potentially a short to +/- or a terminating resistor problem. Inspect the wiring and correct any identified issues.
T
Terry ThompsonAug 23, 2025
What to do if there is no communication from ICU in Mahindra SCORPIO 2014?
- W
  williamslauraAug 23, 2025
  If there is no communication from the ICU, it could be due to several reasons. First, check for disturbances in the CAN wiring, such as shorts or issues with the terminating resistor, and rectify any problems found. Second, ensure the ICU is getting power by checking the wiring and rectifying any issues. Finally, the ICU itself might be defective, in which case it should be replaced.
J
jennifermurrayAug 26, 2025
What to do if the EMS challenge is not acceptable to ICU in Mahindra Automobile?
- C
  Cameron WilsonAug 26, 2025
  If the EMS challenge is not acceptable to the ICU, it could be due to a disturbance in the CAN wiring (short to +/- or terminating resistor). Check the wiring and rectify any issues. Another possibility is that the ECM and ICU are out of sync, in which case you should perform ECM-ICU learning.
G
Gabriela WallaceAug 27, 2025
What to do if the signal from ICU is not received by EMS in Mahindra Automobile?
- D
  Dylan TaylorAug 27, 2025
  If the signal from the ICU is not being received by the EMS, it could be because the ignition was turned on before the EMS After Run completed. Try cranking the engine, turning the ignition off for 2 minutes, and then trying again. Alternatively, the EMS may not be flashed properly. In this case, replace or reflash the EMS and perform EMS learning.
Y
Yvette AyalaAug 30, 2025
What to do if the signal from EMS ECU is not acceptable to ICU in Mahindra Automobile?
- R
  Robert McneilAug 30, 2025
  If the signal from the EMS ECU is not acceptable to the ICU, it's possible that either the EMS or ICU has been replaced without proper pairing. Perform ECM-ICU learning to resolve this issue.
R
Robert PayneSep 1, 2025
What to do if ICU didn’t receive acknowledgement from ECM in Mahindra SCORPIO 2014?
- T
  teresa31Sep 1, 2025
  If the ICU did not receive acknowledgement from the ECM, it could be due to a disturbance in the CAN wiring, such as a short to +/- or a terminating resistor issue. Check the wiring and rectify any problems. It could also be due to a DTC error. Erase the DTC and check if it appears again.
A
Aaron ReynoldsSep 3, 2025
What to do if the acknowledgement received from EMS is not acceptable to ICU in Mahindra Automobile?
- M
  mary17Sep 4, 2025
  If the acknowledgement received from the EMS is not acceptable to the ICU, the cause may be a disturbance in the CAN wiring, such as a short to +/- or a terminating resistor issue. Check the wiring and rectify the issue.
P
Patricia DillonSep 6, 2025
What to do if EMS is not programmed with EMS ID or IMMO ID, hence challenges are not received by ICU in Mahindra SCORPIO 2014 Automobile?
- D
  Danielle KochSep 6, 2025
  If the EMS is not programmed with the EMS ID or IMMO ID, and challenges are not received by the ICU, it is likely that EMS-ICU learning was not performed after flashing a fresh EMS ECU. Check the DTCs and perform the EMS learning.
N
nicholsmarieSep 8, 2025
Why is the signal received from the key cannot be read by ICU in Mahindra Automobile?
- E
  Erik ChaseSep 8, 2025
  If the signal received from the key cannot be read by the ICU, it could be due to a defective key or a defective antenna. Try using both keys to check. If it starts with the second key, replace the first one and perform key learning. If it doesn't start with either key, the antenna may be defective, so replace the ICU and perform the learning.