MAKINEX DPW-4000-VS - User Manual

Questions and Answers

R
Robert DunlapAug 22, 2025
Why is my MAKINEX DPW-4000-VS leaking oil from the pump?
- K
  Kevin GardnerAug 22, 2025
  If there's an oil leak from the MAKINEX Pressure Washer pump, here's what might be happening: * The gaskets may be worn, so replace the gaskets. * The pistons may be worn, so replace the pistons. * The drain plug may be loose, so tighten the drain plug. * The pump may be overfilled, so check for the correct amount. * The incorrect oil may be in use, so drain and refill with the correct type and amount of oil. * The oil seals may be worn, so replace the seals.
M
munozwilliamAug 25, 2025
Why is the pressure fluctuating on my MAKINEX DPW-4000-VS Pressure Washer?
- M
  mullinscrystalAug 25, 2025
  If you're experiencing fluctuating pressure with your MAKINEX Pressure Washer, consider these potential causes: * The valves may be worn, so check and replace them. * The valves may be blocked, so check and replace them. * The pump may be sucking air, so check the water supply and air ingress at joints in the suction line. * The piston packing may be worn, so check and replace it.
G
gallenAug 26, 2025
How to fix water leaking at the pump of MAKINEX DPW-4000-VS?
- L
  Lauren ThompsonAug 26, 2025
  If water is leaking at the pump of your MAKINEX Pressure Washer, it could be due to: * Loose connections, so tighten the connections. * Worn piston packings, so check and replace them. * Worn or broken O-rings, so replace the O-rings. * A pump head or tubes damaged from freezing, so check and replace them.
C
Christine RussoAug 28, 2025
Why is my MAKINEX DPW-4000-VS Pressure Washer pump so noisy?
- S
  Susan LambAug 28, 2025
  If your MAKINEX Pressure Washer pump is noisy, consider the following potential causes: * Air being sucked into the system, so restore the tightness of the intake pipeline connections. * Intake and/or delivery valve springs broken or collapsed, so replace the valves. * Valves blocked by dirt, so clean the valves. * Worn bearings, so replace the bearings. * Intake liquid temperature too high, so reduce the liquid temperature.
R
Raymond SmithAug 30, 2025
What causes MAKINEX DPW-4000-VS pump overheating?
- W
  Wanda OrtizAug 30, 2025
  If your MAKINEX Pressure Washer pump is overheating, it could be due to: * High pump operating pressure, so reduce the pressure to the rated values. * Not enough water flowing through, so check water inflow through pump. * The pump being left on idle for too long; do not leave the pump on idle for more than 2 minutes, as it voids the warranty!
K
Kathleen TerryAug 31, 2025
Why is there a pressure drop in my MAKINEX DPW-4000-VS?
- F
  frazierdonaldSep 1, 2025
  If you're experiencing a pressure drop with your MAKINEX Pressure Washer, it could be due to: * A worn nozzle, so replace the nozzle. * Worn intake and delivery valves, so replace the valves. * Valves blocked by dirt, so clean the valves. * A worn by-pass valve seat, so replace the valve. * Worn gaskets, so replace the gaskets.
O
ovargasSep 2, 2025
What causes irregular variations in pressure in MAKINEX DPW-4000-VS?
- A
  Alexandra CardenasSep 2, 2025
  If you notice irregular pressure variations in your MAKINEX Pressure Washer, it may be caused by: * Worn intake and delivery valves, so replace the valves. * Valves blocked by dirt, so clean the valves. * Air being sucked into the system, so restore the tightness of the intake pipeline connections. * Worn gaskets, so replace the gaskets.
C
Chelsea LowerySep 4, 2025
Why is there water in the oil of my MAKINEX DPW-4000-VS Pressure Washer?
- J
  Jeffery FreySep 4, 2025
  If you find water in the oil of your MAKINEX Pressure Washer, it could be caused by: * A worn guide piston gasket, so replace the gaskets. * A high humidity percentage in the air, so change the oil twice as often. * Worn gaskets, so replace the gaskets.
C
Cody JohnsonSep 6, 2025
How to stop MAKINEX DPW-4000-VS Pressure Washer pump from sucking air?
- J
  Jamie SanchezSep 6, 2025
  If the pump of your MAKINEX Pressure Washer is sucking air, you can try: * Restoring the tightness of the intake line. * Increasing the size of the intake pipelines. * Removing any kinks from the pipes.
D
David LopezSep 8, 2025
What to do if MAKINEX DPW-4000-VS Pressure Washer nozzle is unsuitable or worn?
- A
  Alexis HernandezSep 8, 2025
  If the nozzle of your MAKINEX Pressure Washer is unsuitable or worn, replace the nozzle.