What to do if my Makita Cutter has abnormal vibration and I need to stop the machine immediately?
If your Makita Cutter is vibrating abnormally, it might be due to improper attachment of the wheel. Ensure the wheel is installed as instructed in the manual and that the bolt is tightened to secure it firmly. If the issue persists, the drive system may not be functioning correctly, and you should seek repair from an authorized service center.
What to do if my Makita DCE090ZX2 Cutter cutting tool and motor cannot stop?
If the cutting tool and motor of your Makita Cutter won't stop, immediately remove the battery cartridge and ask your local authorized service center for repair. This could indicate an electric or electronic malfunction.
What to do if wheel rotation is not working properly on my Makita DCE090ZX2 Cutter?
If the wheel rotation of your Makita Cutter does not operate properly even after running the tool without load for 20 seconds, several factors could be at play. Ensure the battery is installed correctly as described in this manual. If the battery power is low, recharge it or replace it if recharging isn't effective. Additionally, the V-belt might be slipping, requiring replacement with a new one. If the issue persists, it is recommended to ask your local authorized service center for repair.
Why does the motor not run on my Makita DCE090ZX2 Cutter?
If your Makita Cutter's motor doesn't run, it could be due to a few reasons. First, make sure that two battery cartridges are correctly installed, as the tool will not function with only one. If the battery is the issue (under voltage), try recharging it. If recharging doesn't work, replace the battery cartridge. If the problem persists, it is recommended to ask your local authorized service center for repair.
What to do if water leaks from the inlet of my Makita DCE090ZX2 Cutter?
If water is leaking from the inlet of your Makita Cutter, specifically from the O-ring part, ask your local authorized service center for repair.
Why does my Makita DCE090ZX2 Cutter have poor cutting performance?
Poor cutting performance on your Makita Cutter likely means it is time to replace the wheel with a new one.
Why does the wheel rotation not accelerate properly on my Makita DCE090ZX2 Cutter?
If the wheel rotation of your Makita Cutter does not accelerate properly, even after running the tool without load for 20 seconds, it could be due to a few reasons. First, ensure the battery is installed correctly as described in the manual. If the battery power is dropping, recharge the battery cartridge; if recharging isn't effective, replace it. The V-belt might also be slipping, requiring replacement with a new one. If these steps don't resolve the issue, the drive system may not be functioning correctly, and you should seek repair from an authorized service center.
What to do if cutting tool and motor cannot stop on Makita DCE090ZX2 Cutter: Remove the battery cartridge immediately?
If the cutting tool and motor of your Makita Cutter won't stop, this could indicate an electric or electronic malfunction. Remove the battery cartridge and ask your local authorized service center for repair.
What to do if my Makita DCE090ZX2 Cutter motor stops running after a little use?
If the motor of your Makita Cutter stops running after a short period, the battery's charge level might be low. Recharge the battery. If recharging is not effective, replace the battery cartridge. Overheating could also be the cause. If so, stop using the tool to allow it to cool down.
What to do if the cutting tool and motor cannot stop on my Makita DCE090ZX2 Cutter?
If the cutting tool and motor on your Makita Cutter cannot be stopped, it indicates an electric or electronic malfunction. Immediately remove the battery cartridge.
General| Battery Type | Lithium-ion |
|---|---|
| Voltage | 18V |
| Cutting Capacity | Up to 90mm |
| Weight | 3.6 kg |
| Blade Diameter | 230 mm |
| Max. Cutting Depth | 90 mm |
| No Load Speed | 6600 rpm |
| Max Cutting Capacity | 90 mm |
| Type | Cordless Cut-Off Saw |
To Next Page
