What to do if the cutting disc runs in idle on my Makita EK6101 Cutter?
If the cutting disc on your Makita Cutter runs in idle, it could be due to several reasons. The idle speed might be incorrect, so adjust it. Check and repair the clutch if it's blocked. If the belt has insufficient tension, address that, and replace the V-belt if it's worn.
What to do if my Makita Cutter engine starts, but dies immediately?
If your Makita Cutter engine starts but immediately dies, the issue could stem from several factors. Check for a dirty suction head or carburetor, and clean them. Ensure the tank venting isn't defective and repair if needed. Also, the idling adjustment could be wrong. Other potential causes include an interrupted fuel line, a defective cable or STOP switch, or a dirty decompression valve. Addressing these areas should resolve the problem.
Why does my Makita EK6101 Cutter engine not start or only with difficulty?
If your Makita Cutter engine doesn't start easily, several factors could be at play. Begin by checking the fuel supply system, wiring, and choke position. Inspect the carburetor for any defects. It may be caused by a malfunction in the compression system, mechanical issues, or a short-circuit in the wiring. Also, a defective plug cap or spark plug could be the culprit. Other potential causes include a dirty suction head, a bent or interrupted fuel line, a defective cylinder base packing ring or radial shaft packings, defective cylinder or piston rings, a spark plug that doesn't seal, a broken spring in the starter, or broken parts inside the engine. Perform necessary repairs after checking these components.
Why does my Makita EK6101 have insufficient power?
If your Makita Cutter is experiencing insufficient power, start by checking the air filter and clean or replace it if dirty. Adjust the carburetor, and clear any clogs in the muffler or exhaust channel in the cylinder.
Defines the proper applications and limitations of the Power Cut saw.
Outlines essential safety rules for operating the Power Cut.
Details necessary personal protective gear for safe operation.
Provides instructions and safety guidelines for handling fuel.
Covers initial setup and safety checks before starting the engine.
Explains the types of discs and their safe usage.
Warns about and explains how to prevent kickback and lock-in hazards.
Guides on correct posture, work area, and cutting techniques.
Specific safety and technique advice for cutting metal.
Safety and technique advice for cutting masonry and concrete.
Instructions for safely transporting and storing the Power Cut.
Specifications and performance data for the Power Cut models.
Diagrams and labels identifying all parts of the Power Cut.
Step-by-step guide for securely installing the cutting disc.
Instructions for preparing and adding the correct fuel mixture.
General guidance and safety for starting the engine.
Detailed steps for starting the engine from a cold state.
Detailed steps for starting the engine when it's already warm.
Instructions on how to safely shut down the engine.
Guidance on carburetor adjustment for optimal performance.
Steps for replacing the V-belt on the Power Cut.
Instructions for cleaning the protective hood for safety.
Procedures for maintaining the air filter for engine health.
Guide on how to replace the spark plug.
Method for verifying the ignition system is functioning.
Instructions for replacing the fuel suction head.
Steps for replacing the starter cable assembly.
Guide on replacing the starter mechanism's return spring.
Recommended schedule for regular maintenance checks.
Importance of using original Makita spare parts.
Conditions and limitations of the product guarantee.
Identifies common malfunctions and their causes/solutions.
Information on optional accessories like diamond cutting discs.
An excerpt from the official spare parts list.
Official statement of compliance with EU directives.
Defines the proper applications and limitations of the Power Cut saw.
Outlines essential safety rules for operating the Power Cut.
Details necessary personal protective gear for safe operation.
Provides instructions and safety guidelines for handling fuel.
Covers initial setup and safety checks before starting the engine.
Explains the types of discs and their safe usage.
Warns about and explains how to prevent kickback and lock-in hazards.
Guides on correct posture, work area, and cutting techniques.
Specific safety and technique advice for cutting metal.
Safety and technique advice for cutting masonry and concrete.
Instructions for safely transporting and storing the Power Cut.
Specifications and performance data for the Power Cut models.
Diagrams and labels identifying all parts of the Power Cut.
Step-by-step guide for securely installing the cutting disc.
Instructions for preparing and adding the correct fuel mixture.
General guidance and safety for starting the engine.
Detailed steps for starting the engine from a cold state.
Detailed steps for starting the engine when it's already warm.
Instructions on how to safely shut down the engine.
Guidance on carburetor adjustment for optimal performance.
Steps for replacing the V-belt on the Power Cut.
Instructions for cleaning the protective hood for safety.
Procedures for maintaining the air filter for engine health.
Guide on how to replace the spark plug.
Method for verifying the ignition system is functioning.
Instructions for replacing the fuel suction head.
Steps for replacing the starter cable assembly.
Guide on replacing the starter mechanism's return spring.
Recommended schedule for regular maintenance checks.
Importance of using original Makita spare parts.
Conditions and limitations of the product guarantee.
Identifies common malfunctions and their causes/solutions.
Information on optional accessories like diamond cutting discs.
An excerpt from the official spare parts list.
Official statement of compliance with EU directives.
General| Engine Displacement | 61 cm³ |
|---|---|
| Fuel Tank Capacity | 0.8 L |
| Weight | 8.9 kg |
| Arbor Size | 20 mm |
| Power Output | 3.2 kW |
| Max Cutting Depth | 110 mm |
| Maximum Cutting Depth | 110 mm |
| Power Rating | 3.3 kW |
To Next Page
