Manhattan SG300BT User Manual

U s e r ’ s M a n u a l
SG300BT Wireless Handheld Linear
Imager Bar code Scanner

Manhattan SG300BT Specifications

General

Connectivity	Bluetooth
Charging Time	3 hours
Operating Frequency	2.4 GHz
Operating Range	Up to 10 meters
Supported Barcodes	UPC, EAN, Code 39, Code 128, ITF, Codabar, MSI
Compatibility	Windows, Android, iOS
Light Source	650 nm laser diode
Battery	Rechargeable Li-ion

Summary

Chapter 1 Product Safety

1.1 Safety & Caution

General safety guidelines and warnings for operating the scanner, including handling and environment.

1.2 FCC Warning

Information regarding FCC compliance requirements and potential interference issues.

Chapter 3 Installation of the SG300BT

3.1 SG300BT Unpacking

3.2 SG300BT Cradle Installation

3.3 SG300BT Setup Bluetooth Communication

Instructions for setting up Bluetooth communication between the SG300BT scanner and a cradle.

3.3.1 Pairing

3.3.2 Setup SPP Master Mode Communication

3.3.3 Setup SPP Slave Mode Communication

3.3.4 Setup HID Slave Mode Communication

Chapter 4 Configuring the SG300BT

4.1.1 Changing Scanner Settings with Programming Codes

How to change scanner settings using programming codes by scanning specific barcodes.

4.2 Set All Default Parameter

Resets all scanner and cradle parameters to factory default settings.

4.3 General Process

Outlines the general steps for configuring the scanner using programming barcodes.

4.4 Cradle Interface Selection

Options for selecting the interface mode for the cradle connection.

4.5 Bluetooth Scanner Setup

Configuration options for setting up the SG300BT scanner via Bluetooth.

4.5.2 Scanner Mode

Settings for different scanner modes like Default, SPP Master, and HID Slave.

4.6 Scanner Operation

Settings related to how the scanner operates, including reading modes and beeper options.

4.6.1 Reading Mode

Options for controlling the scanner's reading behavior (Good Read, Trigger, Continuous).

4.7 RS232 Mode Parameters

Configuration options for RS232 communication parameters.

4.7.1 Baud Rate

Settings for the serial communication baud rate.

4.7.2 Data/Stop Bits

Configuration for data bits and stop bits in serial communication.

4.7.3 Parity

Settings for parity bit types (None, Even, Odd, Mark, Space).

4.7.4 Handshaking

Configuration for handshake methods (RTS/CTS, ACK/NAK, XON/XOFF).

4.8 Keyboard Wedge Mode Parameters

Configuration options for Keyboard Wedge interface.

4.8.1 Terminal Type

Selects the terminal type for Keyboard Wedge emulation.

4.8.2 Country/Language

Sets the keyboard layout and language for Keyboard Wedge.

4.9 Output Characters

4.9.1 Select Terminator

Configures the terminator characters sent after each scan.

4.10 Code Type

Enables or disables specific barcode symbologies for scanning.

4.10.1 Barcode Selection

Allows selection of which barcode types the scanner can read.

4.11 UPC/EAN/JAN Parameters

Specific configuration settings for UPC, EAN, and JAN barcode symbologies.

4.11.1 Reading Type

Defines how UPC-A, EAN-13, ISBN, ISSN, etc., are read.

4.11.2 Supplemental Setup

4.11.3 Check Digit Transmission

4.12 Code 39 Parameters

Specific configuration settings for Code 39 barcode symbology.

4.12.1 Type of Code

Selects between standard Code 39 and Italian Pharmacy/Code 32.

4.12.2 Check Digit Transmission

4.12.5 Setup Code Length

Sets fixed or variable length parameters for Code 39.

4.13 Code 128 Parameters

Specific configuration settings for Code 128 barcode symbology.

4.13.1 Reading Type

4.13.2 Check Digit Transmission

4.13.4 Setup Code Length

4.14 Interleave 2 of 5 Parameters

Specific configuration settings for Interleave 2 of 5 barcode symbology.

4.14.1 Check Digit Transmission

4.14.4 Setup Code Length

4.15 Industrial 2 of 5 Parameters

Specific configuration settings for Industrial 2 of 5 barcode symbology.

4.15.1 Reading Type

4.15.2 Check Digit Transmission

4.15.3 Setup Code Length

4.16 Matrix 2 of 5 Parameters

Specific configuration settings for Matrix 2 of 5 barcode symbology.

4.16.1 Check Digit Transmission

4.16.2 Setup Code Length

4.17 CODABAR/NW7 Parameters

Specific configuration settings for Codabar/NW7 barcode symbology.

4.17.1 Setup Start/Stop Characters upon Transmission

4.17.3 Setup Code Length

4.18 Code 93 Parameters

Specific configuration settings for Code 93 barcode symbology.

4.18.1 Check Digit Transmission

4.18.2 Setup Code Length

4.19 Code 11 Parameters

Specific configuration settings for Code 11 barcode symbology.

4.19.1 Check Digit Transmission

4.19.2 Setup Code Length

4.20 MSI/Plessey Code Parameters

Specific configuration settings for MSI/Plessey barcode symbology.

4.20.1 Check Digit Transmission

4.20.2 Setup Code Length

4.21 Telepen Parameters

Specific configuration settings for Telepen barcode symbology.

4.21.1 Type of Code

4.21.2 Check Digit Transmission

4.21.3 Setup Code Length

4.22 GS1 Databar Omnidirectional Parameters

Specific configuration settings for GS1 Databar Omnidirectional barcodes.

4.22.1 Check Digit Transmission

4.23 GS1 Databar Limited Parameters

Specific configuration settings for GS1 Databar Limited barcodes.

4.23.1 Check Digit Transmission

4.24 GS1 Databar Expanded Parameters

Specific configuration settings for GS1 Databar Expanded barcodes.

Chapter 5 Miscellaneous Parameters

5.2 Preamble and Postamble Insertion

5.2.1 Setup Insertion

5.3 Character Deletion

Quick Configuration