What to do if the time of day flashes on and off on my Marlo Incorporated MGTE Clock?
If the time of day display is flashing, it likely means there was a power outage lasting more than two hours, the transformer was unplugged and plugged back in, or the NEXT and REGEN buttons were pressed, resetting the valve. To resolve this, simply reset the time of day.
Why does my Marlo Incorporated MGTE control valve regenerate at the wrong time of day?
The control valve might be regenerating at the wrong time of day due to several reasons: * Power outages may have occurred. * The time of day may not be set correctly. * The regeneration time is incorrect. * The control valve is set at 'on 0' (immediate regeneration). * The control valve is set at NORMAL + on 0. To fix this, reset the control valve to the correct time of day, ensuring the a.m./p.m. setting is accurate. Also, reset the regeneration time, and check the control valve set-up procedure, especially the regeneration time option.
What to do if my Marlo Incorporated Clock control valve does not regenerate automatically but does when REGEN button is depressed?
If your control valve only regenerates when the REGEN button is pressed, but not automatically, it could be due to: * A by-pass valve being in the bypass position. * A disconnected meter connection. * A restricted or stalled meter turbine. * A defective meter. * A defective PC board. * A set-up error. To solve this, put the control valve in the service position, connect the meter to the PC board, remove the meter and check for rotation or foreign material, replace the meter if defective, replace the PC board if defective, and check the control valve set-up procedure to correct any errors.
What to do if my Marlo Incorporated MGTE Clock timer does not display the correct time of day?
If the timer is showing the wrong time, it might be because: * The outlet is switched. * There was a power outage. * The PC board is defective. To fix this, use an uninterrupted outlet, reset the time of day after a power outage, or replace the PC board if it's defective.
How to fix a Marlo Incorporated Clock control valve that is stalled in regeneration?
If the control valve is stuck during regeneration, the possible causes are: * The motor is not operating. * There is no electric power at the outlet. * The transformer is defective. * The PC board is defective. * The drive gear or drive cap assembly is broken. * The piston retainer is broken. * The main or regenerant piston is broken. To resolve this, replace the motor, repair the outlet or use a working one, replace the transformer, replace the PC board, replace the drive gear or drive cap assembly, replace the drive cap assembly, or replace the main or regenerant piston.
What to do if my Marlo Incorporated MGTE timer does not display time of day?
If the timer isn't showing the time, check these possible causes: * The transformer might be unplugged. * There might be no power at the outlet. * The transformer could be defective. * The PC board might be defective. To solve this, connect the power, repair the outlet or use a working one, replace the transformer, or replace the PC board.
What to do if my Marlo Incorporated MGTE control valve does not regenerate automatically when REGEN button is depressed and held?
If the control valve fails to regenerate automatically when the REGEN button is depressed and held, check for these issues: * The transformer is unplugged. * There is no electric power at the outlet. * The drive gear or drive cap assembly is broken. * The PC board is defective. To fix this, connect the transformer, repair the outlet or use a working one, replace the drive gear or drive cap assembly, or replace the PC board.
What to do if there is no softening/filtering display when water is flowing in my Marlo Incorporated MGTE Clock?
If there's no softening/filtering display while water is flowing, it could be due to: * The bypass valve being in the bypass position. * The meter connection being disconnected. * A restricted or stalled meter turbine. * A defective meter. * A defective PC board. To resolve this, put the bypass valve in the service position, connect the meter to the PC board, remove the meter and check for rotation or foreign material, replace the meter, or replace the PC board.
Detailed steps for loading gravel and resin into the softener tank, including important precautions.
Instructions for securely mounting the control valve onto the softener tank, ensuring a proper seal.
Guidelines for connecting all fittings, including drain and overflow lines, with essential safety notes.
Steps to pressure test the installed plumbing system for leaks and proper operation before full use.
Details the operation and cycle sequences of the automatic control valve for water softeners and filters.
Guides the installer through setting critical parameters like water hardness, regeneration intervals, and regeneration times.
Details specific settings for water hardness, regeneration days, and regeneration time (hour and minutes).
Instructions for servicing and installing 1-1/2" and 2" meter assemblies, including turbine replacement.
Continues the troubleshooting guide, covering additional problems and solutions for the control valve and timer.
General| Brand | Marlo Incorporated |
|---|---|
| Model | MGTE Series |
| Category | Clock |
| Language | English |
To Next Page