Need help?Do you have a question about the MARMON ANGELO PO ACT.O and is the answer not in the manual?
Details the commercial code structure for identifying ACTO oven models and their features.
Lists available gas and electric oven models across different sizes and configurations.
Illustrates the electrical connections and dimensions for electric ACTO ovens.
Shows the gas connections and dimensions for gas-fired ACTO ovens.
Specifies minimum dimensions required for oven passage, including reduction options.
Provides essential guidelines for oven placement, clearances, and utility connections.
Details electrical requirements, features, and voltage switching for electric ovens.
Outlines gas supply requirements, nozzle changes, and dynamic pressure checks.
Explains the steam control system, including the vent pipe and motorized valve.
Describes how the steam vent system functions with the motorized valve open.
Details the operation of the steam vent system when the motorized valve is closed.
Explains how the vent valve is used in different cooking modes like Convection and Combi.
Describes the tank that collects washing fluid and condensation.
Explains the siphon's function in collecting and draining liquids, including overflow.
Details the components of the water inlet units, including filters, valves, and flow meters.
Explains how water is injected into the vent pipe to cool steam and maintain drain temperature.
Describes the water control for steam generation and available options.
Provides a table correlating oven models with dispenser types, flow rates, colors, and codes.
Identifies the main electronic components of the oven's control system.
Guides users on accessing and navigating the oven's service menu.
Explains how to update the oven's software and firmware using a USB key.
Describes various test functions available for checking oven components and operation.
Details how to perform Input/Output tests to check relays on the power board.
Outlines the steps for performing an emergency software update procedure.
Explains the three modes of Wi-Fi connectivity: Hotspot, Client, and Cloud.
Describes the direct network connection using a LAN cable and IP address configuration.
Covers the inverter's function, programmable speeds, and troubleshooting alarm codes.
Details the location and rating of fuses on the power board and transformer.
Explains the basic operation of the total premixing gas system.
Details the three distinct power output levels and their modulation.
Illustrates the interface between main components like panel board and control boards.
Diagram showing the layout of various gas system components.
Describes how to adjust the gas valve using the PR.ADJ screw.
Shows the air-gas mixer and its related components.
Details the burner blower's power supply, speed control, and notes.
Identifies the combustion control board and its jumper positions.
Explains the spark generator's power supply and connection.
Provides notes on checking and replacing spark plugs and flame detectors.
Details the burner's components like flame stabilization mesh and insulation.
Illustrates the heat exchanger and its relation to the combustion chamber.
Describes the exhaust extraction kit and cautions against external connections.
Explains the step-by-step operating logic of the combustion control board.
Diagram illustrating the sequence of events during a standard ignition cycle.
Details the E12:F4 alarm for failed flame detection during ignition attempts.
Guide for preparing and performing gas testing, including gas type changes.
Instructions for analyzing combustion fumes (CO2, CO) using a portable analyzer.
Step-by-step guided procedure for setting up the gas system.
Table of recommended CO2 and CO values for various gas types and models.
Explains how to adjust gas board parameters, such as blower speed, via the Setup Gas menu.
Troubleshooting guide for common issues encountered during gas testing procedures.
Information on completing the installation report with connection and gas analysis data.
Lists gas alarm codes, problems, and corresponding solutions for troubleshooting.
Details the warning for periodic fumes analysis required for gas ovens.
Overview of the washing system's recirculation type and manual/automatic loading.
Lists the three main washing program categories: Washing, Decalcification, and Rinse.
Details the macro-phases, product, duration, and water usage for washing programs.
Outlines the macro-phases for decalcification programs using chemical treatments.
Details rinse-only programs that do not use chemicals.
Illustrates the operation of key components within the washing system.
Step-by-step guide to testing the washing pump's functionality.
Table listing washing alarms, display codes, notes, and service troubleshooting steps.
Explains how to exit the washing menu and safety precautions when interrupting washing.
Describes how to set timers for washing warnings and blocking cooking cycles.
Explains the descaler warning that appears based on user-set time limits.
Guide to configuring washing-related user settings like cleaning time limits and notices.
Details warnings that appear during oven startup related to washing and descaling.
Step-by-step instructions for replacing the encoder component.
Guide for safely replacing the motor, including shaft sealing system details.
Instructions for removing and replacing the micro door switch.
Procedure for disassembling the oven door's inner glass and frame assembly.
Explanation of the cooling system, including fans, intake slots, and filters.
Guidance on cleaning and maintaining the component compartment air filters.
Illustrates the airflow path within the component compartment for different oven models.
General diagram showing the layout and distribution of cooling fans.
Details how to check and adjust the oven door for proper alignment and sealing.
Instructions for replacing the core probe and its connection to the motherboard.
Guide for replacing the humidity detection probe and its connections.
Explains the lamp fixing system and procedures for replacing the halogen lamp.
Procedure for disassembling the lock mechanism and replacing the handle.
Instructions for replacing the spark plug and its associated gasket.
Guide for replacing the blower, including checking mixture diaphragm assembly.
Steps for replacing CPU, Power Board, and Display components.
Procedures for replacing the washing pump and water inlet units.
Instructions for removing and replacing the drain valve actuator.
Overview of the GPAT automatic washing pump group and its main components.
Table specifying torque settings for critical components during assembly.
Details alarms related to low water flow to the chamber or drain.
Lists alarms for door switch faults, washing warnings, and descaler warnings.
Comprehensive table of gas alarms, problems, and troubleshooting solutions.
Details alarms for chamber, core, drain probe faults, and board errors.
Covers inverter alarms, configuration errors, and board communication issues.
Lists alarms for NTC sensor faults, ROI system issues, and gas testing failures.
To Next Page
General
