Martin Yale 7000E User Manual

Model 7000E Commercial Cutter
Installation, Maintenance, & Operating Instructions
Model 7000E Specifications
Thickness Capacity (24# bond) . . . . . . . . .1 1/2"
Width Capacity (With Stop) . . . . . . . . . . . . . .12"
Length Capacity . . . . . . . . . . . . . . . . . . . . . . .12"
Cutting Method . . . . . . . . . . . . . . . . . . . . . .Lever
Clamping Method . . . . . . . . .Manual Handwheel
Dimensions . . . . . . . . . . . . . . .19" x 19" x 13 1/8"
Shipping Weight . . . . . . . . . . . . .48 lbs. (21.8 kg)
Table of Contents
1.0 Parts . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
2.0 Installation . . . . . . . . . . . . . . . . . . . . . Page 2
3.0 Operation. . . . . . . . . . . . . . . . . . . . . . Page 2
4.0 Maintenance . . . . . . . . . . . . . . . . . . . Page 3
5.0 Parts List . . . . . . . . . . . . . . . . . . . . . . Page 6
6.0 Parts Diagram . . . . . . . . . . . . . . . . . . Page 7
7.0 Troubleshooting. . . . . . . . . . . . . . . . . Page 8
Serial # ____________________
INTRODUCTION
Thank you for selecting the Martin Yale Model 7000E Commercial Cutter. The 7000E has been performance-tested at the
Martin Yale factory. With recommended maintenance, the unit will provide years of trouble-free service. Please review
this publication in its entirety before attempting to operate your 7000E. Thorough understanding of this information will
help eliminate most operator-associated errors and ensure years of trouble-free performance.
WARNING! The cutting blade of the 7000E is extremely sharp. Never place hands or fingers under
the cutting blade or into the cutting area. Serious bodily injury could result. Never allow children to
operate the 7000E unsupervised. The weight of the handle can cause the cutting blade to drop if the
spring-loaded safety arm is not fully engaged. Always make sure the spring-loaded safety arm is fully
engaged upon the completion of each cut by returning the handle to the full upright position. Test for
safety arm engagement before releasing the handle.

Martin Yale 7000E Specifications

General

Warranty	1 year limited
Cutting Length	15 inches
Cutting Width	12 inches
Cutting Throat	15 inches
Power	Electric
Safety Features	Safety guard

Summary

Model 7000E Cutter Installation

Model 7000E Operation

Model 7000E Maintenance

Lubrication

Routine lubrication points for moving parts like clamp screw, plate slots, and handle assembly.

Blade Sharpening

Guidance on when and how to sharpen the cutting blade for optimal performance.

Adjustments

Procedures for adjusting the cutter for optimal performance and accuracy.

Model 7000E Parts Replacement

Rotating or Replacing The Cutting Stick

Instructions for rotating or replacing the cutting stick to maintain cut quality.

Blade Removal

Detailed steps for safely removing the cutting blade from the machine.

Blade Installation

Detailed steps for safely installing a new or re-sharpened cutting blade.

Model 7000E Parts List

Model 7000E Parts Diagram

Model 7000E Troubleshooting

Paper Not Completely Cut

Addresses incomplete cuts due to worn cutting stick or blade alignment.

Excessive Pressure Necessary To Complete A Cut

Troubleshooting guide for when extra force is needed to cut paper stacks.

Cut Paper Is Out Of Square

Solutions for misaligned cuts and improper paper stacking or clamping.

The Clamp Wheel Is Hard To Turn

Fixes for a stiff clamp wheel, often related to lubrication needs.

The Handle Is Hard To Move Up Or Down

Troubleshooting for a stiff cutting handle, typically needing lubrication.

The Blade Cuts On One Side But Not The Other

Diagnosing and fixing blade leveling issues for consistent cuts.

The Blade Cuts In The Center Only

Identifies a bad cutting stick as the cause for center-only cuts.