MartinLogan Motion Vision X

To Next Page

contents

top panel controls remote control

standard

controls

power

and menu

access

controls

program soundbar to respond to a second remote

Start with the soundbar remote:

1) Press the “MENU” button.

2) Press down until you see the “LEARN” option. Press enter.

3) Press down and choose the command you want to program.

4) Press enter and the soundbar will respond with “PUSH.BTN”.

Hold the second remote approximately 12-inches (30cm) from the

soundbar and press the appropriate button on the second remote four

times. If the command is learned successfully the soundbar will display

"SET". If it is not learned the soundbar will display "FAILED".

Continue with the second remote:

television: turn off speakers / turn on audio output

When utilizing the soundbar to reproduce audio, the television's speakers should be

turned off. Some televisions will allow you to turn off the internal speaker via the

television's menu system. Other televisions may require you to turn the television's

volume to "zero" or to "mute" the television. Please refer to your television’s manual.

To pass audio out of your television, you may need to turn on the television’s digital

audio out and set it for multi-channel output. Please refer to your television’s manual.

quick start guide

connecting a subwoofer

no subwoofer

wired subwoofer connection

wireless subwoofer connection

adjusting your subwoofer’s controls (wired and wireless connections)

This is the factory default setting. If you are not using a separate subwoofer, use

the soundbar's menu system and choose "SUB > NO SUB". This sets the

soundbar to reproduce the entire frequency range when playing content.

Using a high-quality RCA style cable designed for subwoofer connection,

connect "Sub Out" from the soundbar to the "LFE In/Sub In" on the subwoofer.

Use the soundbar's menu system and choose 'SUB > WIRED'.

Select MartinLogan subwoofers are equipped with a built-in SWT-2 wireless

receiver capable of establishing a wireless connection with this soundbar.

Use the soundbar's menu system and choose 'SUB > WIRELS > SYNC'. The

soundbar will display 'PSH.BTN' [PUSH BUTTON].

Press the subwoofer's sync button and hold for 3 seconds. The subwoofer's LED

will blink quickly. If pairing has completed successfully the subwoofer's LED will

stop blinking and remain on and the soundbar will display 'SYNCED'. Please

note: If a link is not established after 30 seconds the subwoofer's LED will start

blinking slowly and the soundbar will display 'FAILED'. Repeat if syncing fails.

Reference your subwoofer's manual to learn how to properly adjust the sub's

level and phase controls to achieve proper blending with the soundbar. The

subwoofer's crossover should be set to "bypass" or "LFE". For subwoofers that do

not have a "bypass" or "LFE" crossover setting we recommend adjusting the

crossover to its highest setting.

Blu-ray/DVD players: configure multi-channel output

If your soundbar is not producing sound or surround sound from your Blu-ray player,

DVD player, or other multi-channel audio capable source you may need to set the

player’s digital audio output to “Bitstream” (also called “Raw”, “Direct Digital”, or

“High Bit Rate”). If “PCM” is selected you’ll lose the multi-channel encoded sound.

Some players only require you to turn PCM off to configure for multi-channel

encoded sound. Please refer to your player’s manual.

connections

Television

[connect to Digital Optical Audio Out]

Multi-Channel Audio/Video Sources:

Blu-ray, DVD, Game Console,

Cable Box, Satellite Tuner, Etc.

[connect to Digital Optical Audio Out]

[digital optical][digital optical]

power cord

digital

optical cable

remote

control

wall

bracket

wall mount installation template

60 inch

(152 cm)

78 inch

(198 cm)

[Sub Out]

Purple

[AC Power In]

[Optical In]

[Ethernet In]

[Coax In]

Orange

[Analog In]

[IR In]

Digital OutDigital Out

[next

input]

[previous

input]

[volume down]

[volume up]

[mute]

[right]

[left]

[down]

[up]

[enter]

[power off:

]press 2 seconds

[power on]

[access menu:

]

press center button

2 seconds

[wi-fi setup & status:

]

WPS setup: press 3 seconds,

access point setup:

press 8 seconds

rev. 003

Need help?

Do you have a question about the MartinLogan Motion Vision X and is the answer not in the manual?

Summary

Connections

Multi-Channel Audio;Video Sources

Lists sources like Blu-ray, DVD, Game Console, Cable Box, Satellite Tuner for connection.

Television Connection

Connects soundbar to television via Digital Optical Audio Out for audio output.

Connecting a Subwoofer

No Subwoofer Setup

Default setting for soundbars without a separate subwoofer to reproduce full frequency range.

Wired Subwoofer Connection

Connects subwoofer using an RCA cable from 'Sub Out' to 'LFE In/Sub In'.

Wireless Subwoofer Connection

Establishes wireless connection using SWT-2 receiver and sync button.

Adjusting Subwoofer Controls

Guidance on setting level, phase, and crossover for proper blending with the soundbar.

Audio Output Configuration

Blu-ray;DVD Player Multi-Channel Output

Configure player's digital audio output to 'Bitstream' for surround sound.

Television Speaker and Audio Output

Turn off TV speakers and enable TV's digital audio out for multi-channel output.

Remote Control and Programming

Top Panel Controls Overview

Describes the buttons on the soundbar's top panel for basic functions.

Remote Control Functions

Details the buttons and modes available on the dedicated remote control.

Program Second Remote

Process to teach the soundbar to respond to commands from another remote.