Masalta MS60-2 - User Manual

Questions and Answers

L
Laura JonesAug 14, 2025
Why is the Masalta MS60-2 travel speed too low and vibration weak?
- R
  Robert FlemingAug 14, 2025
  Why is the Masalta Construction Equipment travel speed too low and the vibration weak? This could be due to several reasons: * The engine speed might be too low. In that case, set the engine speed to the correct RPM. * The clutch could be slipping. If so, check or replace the clutch. * The V-belt might be slipping. Adjust or replace the V-belt. * There may be excessive oil in the vibration mechanism. Drain the excess oil and fill to the proper level. * There may be a malfunction in the vibrator housing. Check the eccentric, gears, and counter weights. * Bearing failure can also be the cause. Replace the bearing. * Insufficient engine output. Check the engine and compression.
R
Raymond WolfAug 17, 2025
What to do if Masalta Construction Equipment is hard to start but there is no spark?
- C
  Cheryl BrownAug 18, 2025
  What to do if my Masalta Construction Equipment is difficult to start, even though fuel is available, but there's no spark at the spark plug? This could be due to: * Spark plug bridging. Check the gap, insulation, or replace the spark plug. * Carbon deposit on the spark plug. Clean or replace the spark plug. * Short circuit due to deficient spark plug insulation. Check the spark plug insulation and replace it if worn. * Improper spark plug gap. Set it to the proper gap.
J
John SmithAug 21, 2025
What to do if Masalta Construction Equipment is hard to start but compression is low?
- K
  katherine86Aug 21, 2025
  What should I do if my Masalta Construction Equipment is difficult to start, even though fuel is available, a spark is present, and compression is low? The possible causes are: * Suction/exhaust valve stuck or protruded. Re-seat the valves. * Piston ring and/or cylinder worn. Replace the piston rings and/or piston. * Cylinder head and/or spark plug not tightened properly. Torque the cylinder head bolts and spark plug. * Head gasket and/or spark plug gasket damaged. Replace the head and spark plug gaskets.
K
kristen98Aug 25, 2025
What to do if Masalta MS60-2 is hard to start but there is spark?
- M
  Michael McknightAug 26, 2025
  What should I do if my Masalta Construction Equipment is difficult to start, even though fuel is available and a spark is present at the spark plug? Here's what might be happening: * The ON/OFF switch might be shorted. Check the switch wiring and replace the switch if necessary. * The ignition coil could be defective. Replace the ignition coil. * The spark gap might be improper, or the points dirty. Set the correct spark gap and clean the points. * The condenser insulation might be worn or short circuiting. Replace the condenser. * The spark plug wire could be broken or short circuiting. Replace the defective spark plug wiring.
J
James CampbellAug 28, 2025
What to do if there is no fuel present at the carburetor in Masalta Construction Equipment?
- M
  Mary CostaAug 28, 2025
  What to do if there is no fuel present at the carburetor of my Masalta Construction Equipment? The following reasons could be the cause: * Fuel not available in the fuel tank. Fill with the correct type of fuel. * Fuel cock does not open properly. Apply lubricant to loosen the fuel cock level; replace if necessary. * Fuel filter clogged. Replace the fuel filter. * Fuel tank cap breather hole clogged. Clean or replace the fuel tank cap. * Air in the fuel line. Bleed the fuel line.
O
ohowardAug 31, 2025
Why is Masalta Construction Equipment hard to start with normal compression?
- M
  Mr. Jimmy PetersAug 31, 2025
  Why is my Masalta Construction Equipment difficult to start when fuel is available, there's a spark, and compression is normal? This could be due to: * Using the wrong fuel type. Flush the fuel system and replace it with the correct type of fuel. * Water or dust in the fuel system. Flush the fuel system. * A dirty air cleaner. Clean or replace the air cleaner.
L
lknightSep 3, 2025
What causes 'weak in power' but mistires in Masalta Construction Equipment?
- S
  Sandra GonzalezSep 4, 2025
  What causes 'weak in power' with proper compression but misfiring in Masalta Construction Equipment? The issue may be due to: * Water in the fuel system. Flush the fuel system and replace it with the correct type of fuel. * Dirty spark plug. Clean or replace the spark plug. * Defective ignition coil. Replace the ignition coil.
D
Donald HaleSep 6, 2025
Why does the engine of Masalta MS60-2 overheat?
- K
  kristenphillipsSep 7, 2025
  Why does the engine of my Masalta Construction Equipment overheat? It could be due to: * Improper spark plug heat value. Replace it with the correct type of spark plug. * Incorrect type of fuel. Replace it with the correct type of fuel. * Dirty cooling fins. Clean the cooling fins.
C
csteeleSep 12, 2025
Why does the rotational speed of Masalta Construction Equipment fluctuate?
- A
  Ashley HolmesSep 12, 2025
  Why does the rotational speed of my Masalta Construction Equipment fluctuate? It could be due to: * The governor not being adjusted correctly. Adjust the governor. * A defective governor spring. Replace the governor spring. * Restricted fuel flow. Check the entire fuel system for leaks or clogs. * The recoil mechanism clogged with dust and dirt. Clean the recoil assembly with soap and water.