The AST-300H Electronic Muscle Stimulator is designed to contract and relax muscles in the feet and throughout the body, aiming to accelerate blood circulation and alleviate pain, swelling, fatigue, and other related symptoms. This device offers 50 different treatment programs and features a 25-minute automatic timer function. The product has an estimated lifetime of 5 years, which is dependent on electronic aging. Users are advised to contact their local dealer if the product is not functioning properly.
Intended Use:
The AST-300H is intended for use as an electronic muscle stimulator in household environments for typical housekeeping functions. It is also suitable for non-expert users in similar working environments such as shops, offices, farmhouses, hotels, motels, and bed and breakfast establishments. The device is not intended for use by individuals (including children) with reduced physical, sensory, or mental capabilities, or a lack of experience and knowledge, unless they are supervised or instructed by a person responsible for their safety. This product is designed for indoor use only and is not intended for professional use.
Main Parts (Image 1):
- 1 Electrode silicone area for feet
- 2 User manual
- 3 Button
- 4 Adapter
- 5 LCD screen
- 6 Handle
- 7 Electrode pads
- 8 Remote controller
- 9 Electrode wire
- SOLE +: Increases the intensity of the electrode silicone area for feet.
- MODE +: Selects a different mode upwards.
- BODY +: Increases the intensity of the electrode pads.
- SOLE -: Decreases the intensity of the electrode silicone area for feet.
- MODE -: Selects a different mode downwards.
- BODY -: Decreases the intensity of the electrode pads.
Technical Specifications:
- Model number: AST-300H
- Electrical class: Class II
- Product rating input: 5 Vdc - 1A
- Power adapter input: 100 - 240 Vac, 50/60 Hz
- Power adapter output: 5 Vdc - 1000 mAh
- Output waveform: Square wave
- Pulse repetition frequencies: 10 - 100 Hz
- Maximum amplitude of output voltage: 72 V
- Radio frequency range: 50 - 60 Hz
- Pulse duration: 115 µs
- Effect of load impedance: 1 KΩ
- Maximum altitude: 3000 m
- Weight: 3.05 kg
- Frequency response: 110V-240V- 50 Hz/60 Hz (5V-1A)
- Operation condition: 10-40 °C, <80% RH, 860-1060 hPa
- Store and transport condition: 10-40 °C, <80% RH, 860-1060 hPa
Usage Features:
Inserting Batteries in the Remote Control:
- Open the battery cover.
- Place 2 AAA batteries in the battery compartment.
- Close the battery cover.
Using the Electrode Silicone Area for Feet:
Before use, ensure the MODE intensity level, SOLE intensity level, and time are displayed on the LCD screen.
- The mode can be changed while the product is in use, but the intensity will be reset when the mode is changed.
- Adjust the intensity gradually from a lower to a higher setting.
- Place your feet on the electrode silicone area for feet.
- Press the on/off button for 3 seconds to switch on the product.
- Press MODE + and MODE - to select different modes (refer to the "Using the Available Modes" section for a complete list).
- Press SOLE + to increase the intensity; press SOLE - to decrease it.
- Press the on/off button for 3 seconds to switch off the product or terminate the massage early.
For more information on treating different reflexive zones via the electrode silicone area for feet, refer to Image 3.
Placing the Electrode Pads:
- Place electrode pads on the shoulder and/or back for muscle aches (refer to Image 4 for examples).
- Place electrode pads on the waist for muscle aches (refer to Image 5 for examples).
- Place electrode pads on the arm for numbness or muscle aches (refer to Image 6 for examples).
- Place electrode pads on the leg for muscle aches (refer to Image 7 for examples).
Using the Electrode Pads:
- Do not stick two electrode pads to each other.
- Keep electrode pads away from high temperatures and direct sunlight.
- Do not touch electrode pads with your fingers.
- Do not clean electrode pads with hot water or aggressive chemical cleaning agents.
- Keep electrode pads clean.
- Protect electrode pads by reattaching the protective membrane after use.
- Replace electrode pads if they have not been used for a year.
- Connect the electrode wire to the electrode pads.
- Connect the electrode wire to the electric muscle stimulator.
- Remove the protective membrane from the electrode pads.
- Attach the electrode pads steadily to the skin (refer to "Placement of the Electrode Pads" for examples).
- Press the on/off button for 3 seconds to switch on the product.
- Adjust the mode and intensity as desired.
Available Modes (Image 2):
The device offers 25 different modes, including:
- Acupuncture / Pushing
- Acupuncture
- Acupuncture / Kneading
- Acupuncture / Tapping
- Scrapping
- Squeezing
- Massage
- Pushing / Massage
- Pushing / Squeezing
- Acupuncture / Squeezing
- Acupuncture / Hammering
- Kneading
- Thumping
- Scrapping / Pressing
- Cupping
- Body Shaping
- Hammering
- Massage / Tapping
- Pushing
- Rolling / Pounding
- Squeezing
- Stroke
- Acupuncture / Massage
- Shiatsu
- Rolling / Kneading
Maintenance Features:
- Products must be disconnected from their power supply during cleaning or maintenance.
- Clean the product after each use.
- Wipe the machine with a wet cloth or neutral cleanser.
- Wipe the electrode pads with a wet cloth if they are insufficiently adhesive or dirty; if this does not help, replace them.
- Do not use aggressive chemical cleaning agents such as ammonia, acid, or acetone when cleaning the product.
Storage:
- Store the product away from magnetic fields.
- Store the product out of reach from children.
- Store the product away from moisture, high temperatures, direct sunlight, and sprinkling water.
- Remove the batteries from the controller when the product is not used for a long time.
Troubleshooting:
- No stimulation:
- Wire disconnected: Connect the wire.
- Protective membrane not removed from pads: Remove the protective membrane.
- Weak stimulation:
- Pads not stuck tightly: Stick the pads tightly.
- Pads stuck overlapped: Detach and stick the pads again.
- Pads dirty: Clean the pads.
- Intensity weak: Increase the intensity.
- Pads placed wrong: Detach and stick the pads again.
- Skin becomes red and stings:
- Therapy duration too long: Decrease the therapy time.
- Pads too dry: Clean the pads with a wet cloth.
- Pads not stuck tightly: Stick the pads tightly.
- Pads dirty: Clean the pads.
- Pads damaged: Change the pads.
- Power cuts off during therapy:
- Pads fell off skin: Turn off power and stick the pads again.
- Wire of pads cut power off: Turn off power and connect the pads again.
- Battery empty: Change the battery.
- Therapy time over: Power will turn off automatically after 15 minutes.
To Next Page
Need help?
General
