Dear customer, thank you for purchasing a MASTER product. This guide contains information about the product use. Before the product installation and use, please read carefully this
guide and keep it for future reference. The device is designed for the control of tubular motors for moving awnings and the like.Any other use beyond the field defined by Master S.p.A. is
prohibited and involves, as well as the failure to comply with instructions provided in this guide, the cancellation of Master S.p.A. liability and warranty. The installer, after the installation
of the product, must teach the end user about the working way of the automation and provide him with the user manual.
This sensor does not protect awning in case of strong and sudden gusts of wind. In case of weather hazards of this type, make sure that the curtains remain closed! Master S.p.A.
declines all responsibility for damage incurred due to weather events not detected by the device.
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
Disposal
It is advisable (for example, near police stations, airports, ports, hospital, etc). A technical inspection is in any
case advisable before installing any radio system in order to identify sources of interference.
to avoid using radio systems in areas with strong interference
Radio systems can be used where possible disturbances or malfunctioning of the transmitter or the receiver do not cause a risk factor, or if the risk factor is cancelled by suitable
safety systems. The presence of radio device operating on the same transmission frequency ( ) can interfere with the radio receiver of the motor and so reduce the range
of the system and limit the functionality of the installation.
433,42 MHz
Notes on radio systems
Power supply: 3V CR8-LHC battery
Dimensions: 236 x 54 x 73 mm
Weight: 200 gr
Operating temperature: –20°C / +55 °C
Wind threshold: 10 Km/h / 35 Km/h
TECHNICAL SPECIFICATIONS
BLAST BT
battery-powered radio wind sensor
VEGA BT
battery-powered radio sun/wind sensor
rev04_1 11.07.2022
To power the sensor slide the switch from
OFF (1) to ON
(2)
1
ON
Fix the wall support
through the supplied
plugs and screws
A
Close the two screws
that fix the wall support
and sensor
B
Insert the two screw
cover
C
Unscrew the screw and
open the closing cover
placed under the sensor
D
E F
Close the cover
(1)
(1) this screws must never be completely unscrewedWARNING:
(2) WARNING: when you slide the switch in the ON position, the LED1 should light up brieflyIf LED1 do not turn on, return the switch to OFF (1) position, wait 30 seconds and repeat.
R
433,42 MHz
Incorrect installation can cause serious injuries Keep these instructions for future maintenance work and disposal of the product All the product installation, connection,
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician Some applications require hold-to-run
operation and can exclude the use of radio controls or require particular safety devices To prevent potentially dangerous situations, check the operating condition of the roller
shutter/awning regularly
● ●
● ●
●
1.1 SAFETY warnings for the USER
Read the technical specifications on the paragraph “Technical specifications” to evaluate the operating limits of the product
Before installing the product, check the compatibility with the associated devices and accessories Check that the package is
intact and has not been damaged in transit A heavy shock and the use of unsuitable tools can cause the damage of the
external or internal parts of the product Do not pierce or tamper with the product in any way. Do not modify or replace parts
without the manufacturer’s permission Check that the place chosen for the installation is made by solid material and can
ensure a stable fixation Check that the place chosen for the installation of the sensor is within the range of transmission-
reception generated by the sensor and by the receiver of the blind to be commanded Install the product with the cups pointing
downwards and with the body of the sensor horizontally (using a bubble level facilitates the operation, the attack on the wall with
tilting angle ± 90 ° allows you to mount the sensor on non-vertical structures) The product must be installed well exposed to
the sun-wind, away from heat sources (eg chimneys), away from obstacles that may interfere with the movement of the cups
If there are several radio appliances in the same system, they must not be less than 1,5m apart Do not install the product near
metal surfaces Do not use abrasive or solvent product for cleaning the device; do not clean using water or high-pressure
cleaners For your safety, do not work near the winding roller while the motor is powered
●
●
●
●
●
●
●
●
●
●
●
●
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they are supervised or given instructions about the product way of use by a person
responsible for their safety Check the automation during the movement and keep people at a safe distance, until the
movement ends Do not allow children to play with the appliance or with the fixed control devices Do not operate the blind
when maintanance operations are being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect
the motor from the power line
●
● ●
1.2 SAFETY warnings for the INSTALLER
1.3 Warnings for USE
X
Led WIND
Button P1
Led SUN
Button P2
Led MANOEUVRE
Button P3
MOUNTING
WARNINGS
Sun threshold (VEGA BT only): 1 Klux / 45 Klux
Operating frequency: 433.42 Mhz
Operating frequency band: 433,050 – 434,790 Mhz
Max radiated power, e.r.p. : <10 mW
Range (estimated): 20m
1
2
To Next Page
Loading...