Mattel BOOMco DYNAMAG

To Next Page

A. Fully load clip with darts.

A. Pull slide all the way back and release.

C. Remove empty clip and reload!

TO LOAD

TO FIRE

CONTENTS

WARNING: Do not aim at eyes or face. Only use projectiles supplied

with this toy. Do not re at point blank range.

TO AVOID INJURY: Do not modify rounds, darts, or dart blaster.

Always wear appropriate eye-wear, sold separately.

CJF20_1100323876_DOM

Please keep these instructions for future reference as they contain important information.

GAUNTLET

INSTRUCTIONS

Services 1-800-524-8697. Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628

500303. Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312.

Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK,

China.

Tel.: (852) 3185-6500.

Diimport & Diedarkan Oleh: Mattel Southeast Asia Pte. Ltd. , No 19-1, Tower 3

Avenue 7, Bangsar South City, No 8, Jalan Kerinchi, 59200 Kuala Lumpur, Malaysia. Tel: 03-78803817, Fax:

03-78803867.

DATE: 08.27.2014

ATTACHING TARGETS

Do not stick target to walls

or furniture as it may cause

damage to the surface.

Peel backing off target before sticking

it to surface.

REMOVING DARTS

CLEANING DARTS

REPLACING TARGETS

& SHIELDS

Y8620/BBY17

Replace time-worn targets and shields with

Y8620/BBY17 SMART STICK™ REFILLS.

Each sold separately, subject to availability.

✖

Dust, dirt, and other debris can cause

darts to lose their adhesiveness.

NOTE: Dry darts before using again.

REMOVE DARTS

TECHNOLOGY !

IMMEDIATELY

TO MAINTAIN SMART STICK™

Keep one hand pressed on target, hold

dart by the tip and gently peel dart o.

To clean darts, rinse darts’ tips with

tap water or use tape to remove

excess debris.

x 6

DYNAMAG™

Press trigger to re!

Pull slide back and press trigger again to re the next dart!

Works with all BOOMco.™ clips.

Insert the fully loaded clip from

the top of the blaster with the

arrowheads pointing down.

INSTRUCTION SHEET

SPECIFICATIONS

Toy:

Toy No.:

Part No.:

Trim Size:

Folded Size:

Type of Fold:

# colors:

Colors:

Paper Stock:

Paper Weight:

EDM No.:

DATE:

CJF20

MAG BLASTER

1100323876

70 gsm

REV.DATE:

One

black

FSC recycled paper

Align marking ( ) to

blaster as shown.

Click!

Need help?

Do you have a question about the Mattel BOOMco DYNAMAG and is the answer not in the manual?

Summary

Attaching Targets

Target Placement Warning

Do not stick targets to walls or furniture as it may cause damage to the surface.

Cleaning Darts

Dart Cleaning Method

Rinse dart tips with tap water or use tape to remove debris. Dry darts before reuse.

Removing Darts

Dart Removal and Technology Preservation

Gently peel dart off target. Remove darts immediately to maintain Smart Stick technology.

Replacing Targets & Shields

Smart Stick Refills

Replace time-worn targets and shields with specific Smart Stick Refills, sold separately.

Safety and Usage Information

General Safety Precautions

Do not aim at eyes or face. Use only supplied projectiles. Do not modify blaster or darts. Wear eye-wear.

Loading the Blaster

Loading the Clip

Fully load the clip with darts, ensuring arrowheads point down.

Inserting the Clip

Insert the loaded clip into the blaster, aligning the marking.

Firing the Blaster

Priming and Firing

Pull the slide back to prime. Press the trigger to fire. Repeat for subsequent darts.

Reloading Procedure

Remove the empty clip and reload for continued play.