Maximum Controls MATRIX III MAX 1500 PRO - Matrix III LED Troubleshooting Continued; Additional LED Status and Solutions

omron E3K-R10K4 wiring for max pro
Polarity does NOT matter
12VDC Out Monitored
4 56
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
24 to 240 VDC
12
N02 C2
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
PHOTO CLS NC
GND
NOTE: To meet the UL 325 2018 standard,
Type B1 Non-Contact sensor entrapment
protection device MUST be MONITORED
by the gate operator.
NORMALLY CLOSED (NC)
UL325-2018
Wiring to E3K Photocell
DO NOT connect
to NC2 #4.
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR N.C.UL SENSOR 10K
NSOR N.C
P
NSOR N.C
P
SOR N.
P
SOR N
P
SOR N
SOR N
OR N
OR N
OR
NC2 N02 C2
IMPORTANT:
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
For 10K Resistor E3K Photocell wiring see next page
UL 2018 Label on packaging
5,3TANDARD-!802/02/&02/-ATRIX))))NSTALL6ERSIONB
Polarity does NOT matter
12VDC Out Monitored
4 56
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
VDC24 to 240
12
N02 C2
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
/0%./.,9.#
GND
NOTE: To meet the UL 325 2018 standard,
Type B1 Non-Contact sensor entrapment
protection device MUST be MONITORED
by the gate operator.
Installation Steps:
 3ETSWITCHTOh,)'(4/.v
2.
3.
7IRE6POWERTOPHOTOCELL
7IRE /0%./.,9.#
TO PHOTOCELL ./
7IRE '.$TOPHOTOCELL #
 !LIGNPHOTOCELLTOREFLECTOR
 !DJUSTSENSITIVITY
UL325-2018
NORMALLY CLOSED (NC)
Wiring to E3K Photocell
DO NOT connect
to NC2 #4.
NC2 N02 C2
IMPORTANT:
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
For 10K Resistor E3K Photocell wiring see next page
UL 2018 Label on packaging
2
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR 10K
UL SENSOR N.C.
Installation Steps:
 3ETSWITCHTOh,)'(4/.v
2.
3.
7IRE6POWERTOPHOTOCELL
7IRE 0(/4/#,3.#
TO PHOTOCELL ./
7IRE '.$TOPHOTOCELL #
 !LIGNPHOTOCELLTOREFLECTOR
 !DJUSTSENSITIVITY
CLOSING Direction
Photocell (Reflector)
OPENING Direction
Photocell (Reflector)