NOTE:
IMPORTANT:
DO NOT use 10K Resistor included with photocell.
456
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
24 to 240 VDC
1
C-1
2
NO1
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
GND
Installation Steps:
omron E3K-R10K4 wiring for max pro
DO NOT connect
to NC1 #3.
Polarity does NOT matter
12VDC Out Monitored
NORMALLY CLOSED (NC)
UL325-2016
Wiring to E3K Photocell
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
NOTE:
DO NOT use 10K Resistor included with photocell.
456
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
VDC24 to 240
1
C-1
2
NO1
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
GND
Installation Steps:
DO NOT connect
to NC1 #3.
Polarity does
NOT
matter
12VDC Out Monitored
UL325-2016
NORMALLY CLOSED (NC)
Wiring to E3K Photocell
IMPORTANT:
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
NOTE:
DO NOT use 10K Resistor included with photocell.
456
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
24 to 240 VDC
1
C-1
2
NO1
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
GND
Installation Steps:
DO NOT connect
to NC1 #3.
OPEN ONLY NC
OPEN ONLY 10K
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR 10K UL SENSOR N.C.SOR NNSOR N.CNSOR N.CSOR NSOR NOR NOR SOR N.OR N
Polarity does NOT matter
12VDC Out Monitored
UL325-2016
NORMALLY CLOSED (NC)
Wiring to E3K Photocell
IMPORTANT:
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
NOTE:
DO NOT use 10K Resistor included with photocell.
456
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
VDC24 to 240
1
C-1
2
NO1
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
GND
Installation Steps:
DO NOT connect
to NC1 #3.
OPEN ONLY NC
OPEN ONLY 10K
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR 10K UL SENSOR N.C.SOR NNSOR N.CNSOR N.CSOR NSOR NOR NOR SOR N.OR N
Polarity does NOT matter
12VDC Out Monitored
UL325-2016
NORMALLY CLOSED (NC)
Wiring to E3K Photocell
IMPORTANT:
Photocell MUST be powered
by 12VDC OUT Monitored or
it will NOT be MONITORED.
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR 10K
UL SENSOR N.C.
PHOTO CLS NC
OPENING Direction
Photocell (Reflector)
CLOSING Direction
Photocell (Reflector)
UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7b
24
To Next Page
Loading...
