MAXTRA ML-44GDRS-ES-E100

Questions and Answers

T
Timothy BakerAug 14, 2025
What to do if my MAXTRA Scooter won't charge or doesn't work?
- D
  David HamiltonAug 14, 2025
  If your MAXTRA Scooter isn't working or charging, there are several things to check: * First, press the reset button. * Then, inspect the connections and wires under the deck plate for any looseness or damage. * Verify that the wall outlet is working, and try a different outlet. * Examine the charger lights: when plugged into the wall, it should be green; when plugged into the wall and the unit, it should be red while charging and green when charging is complete. If there are no lights or blinking lights, replace the charger. * If the light is on after turning on the switch, the controller may have failed and needs replacement. * If the light is not on when the switch is opened, the battery may have failed, and you should replace the controller and batteries.
T
Tina YoungAug 18, 2025
Why does my MAXTRA Scooter have short run time or runs slow?
- K
  Karen WilsonAug 18, 2025
  If your MAXTRA Scooter has a short run time or runs slowly, consider the following: * Ensure the rider weighs no more than 155 pounds. * Only use the scooter on flat, dry surfaces, avoiding slopes and areas with rubble. * Charge the scooter for 9 hours to ensure the battery is full. * The batteries may need to be replaced. * Check if the brake is dragging. Under normal conditions, the rear wheel should turn easily by hand. If the controller still outputs current when braking, check the brake wire connection or replace the brake. In normal braking, the controller should immediately reduce the current output to '0' after holding the brake handle.
N
Nina SanchezAug 21, 2025
What to do if my MAXTRA Scooter runs intermittently?
- J
  Jessica WalkerAug 21, 2025
  If your MAXTRA Scooter runs intermittently, check the wires around the throttle and connectors underneath the deck plate for any loose connections. If the connections are secure, the throttle may have failed and needs to be replaced.
A
april68Aug 25, 2025
What does it mean if the LED indicating lamp on my MAXTRA Scooter flashes 3 times?
- M
  Mrs. Samantha BlairAug 26, 2025
  If the LED indicating lamp on your MAXTRA Scooter flashes 3 times, it indicates over-current protection. To resolve this, turn off the power, press the reset button, and then turn the power back on.
C
Christopher TorresAug 28, 2025
What does it mean if the LED indicating lamp on my MAXTRA Scooter flashes 4 times?
- C
  Cynthia Heath MDAug 28, 2025
  If the LED indicating lamp on your MAXTRA Scooter flashes 4 times, it indicates an output short circuit protection issue. This could be due to a motor short circuit or a short circuit in the controller output (blue, brown wire). Perform troubleshooting and then restart the scooter.
C
Christopher McgeeAug 31, 2025
What does it mean if the LED indicating lamp on my MAXTRA Scooter flashes twice?
- J
  Jacqueline DavisAug 31, 2025
  If the LED indicating lamp on your MAXTRA Scooter flashes twice, it means the scooter is experiencing over-temperature protection. Shut it down for a while and then power it up again.
E
Emily EatonSep 3, 2025
What does it mean if the LED indicating lamp on my MAXTRA Scooter flashes 5 times?
- S
  Sean SaundersSep 3, 2025
  If the LED indicating lamp on your MAXTRA Scooter flashes 5 times, it indicates speed protection is active. The controller likely needs to be replaced.
J
Joseph JohnsonSep 7, 2025
What should I do if the LED indicating lamp on my MAXTRA Scooter has no light?
- J
  jasonortizSep 7, 2025
  If the LED indicating lamp on your MAXTRA Scooter has no light, first check that all wire connections are in good condition. Next, check whether the reset button pops up. If neither of these resolves the issue, replace the batteries or controller.
A
Allen MartinezSep 10, 2025
What to do if the LED indicating lamp lights up but the motor doesn't turn on my MAXTRA Scooter?
- C
  Charles GloverSep 10, 2025
  If the LED indicating lamp lights up on your MAXTRA Scooter, but the motor does not turn, first check that the throttle and motor wires are making good contact. If they are, the throttle or motor may need to be replaced.