Maytag MHWC7500YW User Manual (English)

Other manuals for Maytag MHWC7500YW

Questions and Answers:

L
Lisa WilsonAug 14, 2025
What to do if A09 (Water Inlet Problem) appears on my Maytag MHWC7500YW Washer display?
- T
  Trevor PerezAug 15, 2025
  If A09 (Water Inlet Problem) appears on your Maytag Washer display, it indicates there is no water or insufficient water supply. Ensure both hoses are attached and have water flowing to the inlet valve and that both hot and cold water faucets are on. Also, the inlet valve screens on the washer may be clogged, or there may be kinks in the inlet hose. Check if the water inlet hoses are frozen. Plug in the washer or reconnect the power. Press and hold START to continue the cycle or press and hold CANCEL/DRAIN to cancel the cycle. If the problem remains, call for service.
D
Diane CrawfordAug 17, 2025
What to do if A 1 0 (drain pump system error) appears on my Maytag Washer display?
- A
  Anna HayesAug 17, 2025
  If A 1 0 (drain pump system error) appears on your Maytag Washer display, check the drain hose for proper installation. Ensure the drain hose is not kinked, pinched, or blocked. Remove any clogs from the drain hose. Use the drain hose form and securely attach it to the drainpipe or tub. Lower the drain hose if the end is higher than 55" (1.4 m) above the floor.
T
Todd HardingAug 21, 2025
Why is my Maytag MHWC7500YW leaking water or suds from the door or rear of the cabinet?
- C
  Clifford GregoryAug 21, 2025
  Water or suds leaking from the door or rear of your Maytag Washer cabinet is often due to not using HE detergent or using too much HE detergent. Only use HE detergent, as suds from regular detergents can cause leaking. Always measure detergent and follow the manufacturer’s directions based on your load requirements. Periodically clean the underside of the glass window to avoid potential leaks. The washer senses load sizes and adds the correct amount of water for optimal cleaning.
T
Tiffany HansenAug 25, 2025
Why does my Maytag MHWC7500YW have gurgling or humming noises and water leaks?
- B
  Barbara MartinezAug 25, 2025
  Gurgling or humming noises with water leaks in your Maytag Washer can occur because the washer may be draining water; it is normal to hear the pump making a humming sound with periodic gurgling or surging as final amounts of water are removed during the spin/drain cycles. Check that the fill hoses are attached tightly and that all four fill hose flat washers are properly seated. Also, ensure the drain hose connection is properly secured to the drainpipe or laundry tub. Water can back up out of a clogged sink or drainpipe, so check all household plumbing for leaks (laundry tubs, drain pipes, water pipes, and faucets).
Z
Zachary BeckerAug 28, 2025
Why does my Maytag MHWC7500YW vibrate, rock, or 'walk'?
- R
  richard58Aug 28, 2025
  Your Maytag Washer might vibrate, rock, or 'walk' because the feet may not be in contact with the floor and locked. Both front and rear feet must firmly contact the floor, and the washer must be level to operate correctly. Ensure the jam nuts are tight against the bottom of the cabinet. Also, check if the load is unbalanced or too large. Avoid tightly packing the load and avoid washing single items; balance a single item with a few extra items. It is also possible that the shipping bolts are still in the back of the washer.
W
William BrownAug 31, 2025
Why is my Maytag MHWC7500YW making clicking or metallic noises?
- T
  toddangelaAug 31, 2025
  Clicking or metallic noises in your Maytag Washer can be normal if the door is locking or unlocking, which involves three clicks after pushing START. However, such noises can also be caused by objects caught in the washer drain system. Empty pockets before washing, as loose items like coins could fall between the basket and tub or block the pump. It may be necessary to call for service to remove the items. It is normal to hear metal items on clothing such as metal snaps, buckles, or zippers touch against the stainless steel basket.
A
ariana64Sep 3, 2025
Why is my Maytag Washer load not rinsed properly?
- R
  Rachel FarrellSep 3, 2025
  If your Maytag Washer load is not rinsed properly, it may be due to not using HE detergent or using too much HE detergent. Use only HE detergent, and always measure detergent, following the manufacturer’s directions based on load size and soil level. Ensure the washer is loaded as recommended. Both hoses must be attached and have water flowing to the inlet valve, and both hot and cold water faucets must be on. The inlet valve screens on the washer may be clogged, or there may be kinks in the inlet hose.
S
swestSep 6, 2025
Why does F 0 1 – F 3 0 appear on my Maytag MHWC7500YW Washer display?
- D
  David BestSep 6, 2025
  If F 0 1 – F 3 0 appears on the display of your Maytag Washer, this indicates an electrical problem. Turn the knob to OFF or press and hold START to cancel the cycle. If there is excessive water in the washer, select DRAIN/SPIN. Re-select the cycle and press START. If the problem remains, call for service.
C
Caroline HamiltonSep 9, 2025
Why does my Maytag MHWC7500YW Washer have odors?
- J
  john25Sep 10, 2025
  Odors in your Maytag Washer can be due to not using dispensers, which can lead to chlorine bleach and fabric softener staining. Ensure you wash like colors together and remove them promptly after the cycle is complete to avoid dye transfer. Also, not enough detergent may have been used, or you may have hard water. Use more detergent for washing heavy soils in cold or hard water. Run the Clean Washer cycle with affresh® monthly.