1
1030832 Rev.A 10/05
PART NUMBER (s):
0000-8F-H13
APPLICABLE MODELS:
2006>MAZDA6
ALL MODELS
REMOTE START SYSTEM
VEHICLE PREPARATION
1. Remove the driver’s side lower dash panel.
a. Unclip the hood release by inserting a fiber stick between the
hood release and the dash panel. There is a center tab the
stick must push down while pulling hood release towards the
rear of the vehicle.
b. Remove (2) 8mm bolts behind the hood release cable.
(FIGURE A)
c. Unsnap lower dash panel using a fiber stick starting at the
bottom.
d. Unplug the trunk release connector after removing the lower
dash panel.
2. Remove the driver’s side lower dash kneeblocker bracket (4) phil-
lips head screws and remove bracket. (FIGURE B)
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
BOTH PROGRAMMED IGNITION
KEYS ARE REQUIRED AT TIME
OF INSTALLATION
KIT CONTENTS
Remote Start DNA Card Remote Start Dipole Antenna Remote Start
Control Module (QTY-1) Transmitters (QTY-1) Wire Harness
(QTY-1) (QTY-2) (QTY-1)
P/N: 0000-8F-Z01 P/N: 0000-8F-H16 P/N: 0000-8F-Z02 P/N: 0000-8F-Z10 P/N: 0000-8F-H17
Owner's Manual
Vehicle Remote Start System
TM
Featuring PowerCode Technology
For the Ultimate in Comfort, Convenience and Security
TM
MAZDA
GENUINE ACCESSORIES
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
Immobilizer Interface Adhesive Primer 2- Sided Tape
Module and Harness (QTY-1) (QTY-1)
(QTY-1)
Tie Wrap
(QTY 2)
IDC Wire Tap
(QTY 2)
Hood Safety
Switch
(QTY 1)
Owners
Manual
(QTY 1)
Wallet
Card
(QTY 1)
Underhood
Sticker
(QTY 1)
Long Tie
Wrap
(QTY 4)
Mini Fuses
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
1/4” Self
Drilling Screws
(QTY 2)
PARTS BAG CONTENTS
HOOD SAFETY SWITCH KIT CONTENTS
(P/N: 0000-8F-H03)
Locking
Washer
(QTY 2)
IMMOBILIZER INTERFACE KIT CONTENTS
(P/N: 0000-8F-H05)
Tie Wrap IDC Wire Tap
(QTY-10) (QTY-4)
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
PHILLIPS SCREWDRIVER
POWER DRILL
0
PRE INSTALLATION
1. CLEAN HANDS
2. OPEN DRIVER’S DOOR WINDOW
3. RECORD RADIO STATIONS
4. SET PARKING BRAKE
5. DISCONNECT AND ISOLATE
NEGATIVE BATTERY TERMINAL
6. VEHICLE MUST BE AT ROOM
TEMPERATURE
9/32” DRILL BIT
FIBER STICK
10mm SOCKET AND RATCHET
8mm SOCKET AND RATCHET
1/4” SOCKET AND DRIVE
3/8” DRIVE TORQUE WRENCH
3/8” DRIVE 10mm SOCKET
TOOLS REQUIRED
FIGURE A
FIGURE B
1
To Next Page
Need help?
General
