—
BEFORE STARTING
1. Place the shredder on a firm, level surface.
2. Service engine with gasoline and oil as instructed in the
separate engine manual packed with your shredder.
3. Insure spark plug wire is attached to spark plug.
fA
DANGER
A“
I
BE SURE NO ONE OTHER THAN THE OPERATOR IS
STANDING NEAR THE CHIPPER-SHREDDER WHILE
STARTING OR OPERATING.
r
A
WARNING
A
.
THE CHIPPEWSHREDDER IS SHIPPED WITHOUT
GASOUNEIN THE FUEL TANK AND VERY LlllLE OIL
IN THE ENGINE CRANKCASE. DO NOT OPERATE
ENGINE U.~L CRANKCASE HAS BEEN HUED WITH
OIL AS SPECIFfED IN THE ENGINE MANUAL PRO-
VIDED WfTH THE MACHINE.
TO START ENGIN&
●
●
●
●
●
●
●
●
●
Insure spark plug wire and rubber boot is attached to spark
plug (See
EngineManual).
Turn fuel shutdf valve to ‘ON” position (if so equipped)
(seeEngine Manual).
Push stop switch to “ON” position (if so equipped).
Move choke control lever to “CHOKIVFULL CHOKE”
positiin. (See Engine Manual)
Move throttle control lever to ‘FAST/ON/RUN” positiin.
Grasp starter handle (See Engine Manual) and pull rope
out slowly until engine reaches start of compression cycle
(rope willpullslightly harderatthispoint. Letlhe rope rewind
slowly.
Pull the rope with a rapid, continuous, full arm stroke. Keep
a firm grip on start handle. Let rope rewind slowly. DO NOT
let starter handle snap back against starter.
Repeat preceding two (2) instructions until engine fires.
When engine starts, move choke lever on engine halfway
between ‘CHOKE/FULLCHOKE” and“RUN/NOCHOKE”.
Move throttle control to idle positiin for a few minutes to
allow engine to warm-up. When engine is warm move
choke lever to “RUN positiin.
NOTE Inorderto idlesmoothly, anew engine may requirethree
(3) to five (5) minutes running above slow idle speed. Idle speed
has been adjusted to be correct after this break-in period.
TO STOP ENG9NE:
● Movethrottle control lever to *’OFF/STOP/SLOW position.
(See Engine Manual)
● Push stop switch to “OFF position (if so equipped).
● Do not choke carburetor to stop engine. Backfire or engine
damage may result if choke is used to stop engine.
●
NOTE: Closefuelshutoff valve (ifsoequipped)whentransporting
or not operating Chipper/Shredder, to prevent fuel leakage.
;.,
.-
,., .,..-...
..:
HOW TO USE YOUR
CH9PPER-SHREDDER:
..
The Chipper/Shredder is designed for three (3) different meth-
ods of operation.
A
DANGER
A-
THE CHIPPER-SHREDDER DISCHARGESMATERIALS
WITH CONSIDERABLE VELOCITY. KEEPAWAYFROM
THEAREAAROUND THE DISCHARGE ALWAYS STOP
THE ENGINE AND DISCONNECT THE SPARK PLUG
WfRE WHEN REMOVING OR AITACHING THE BAG
WHEN CHANGING CONTAINERS OR WHEN REMOV-
ING THE SHREDDED MATERIAL. WEAR SAFETY
GLASSES AND GLOVES WHENEVER USING YOUR
CHIPPER-SHREDDER
● Leaves and small branches can be fed into the Hopper
assembly when it is inthe raised positiin (See FfG. 2-OP).
If it becomes necessary to push material into the Chipper/
Shredder, use the suppfied debris tamper - NOT YOUR
●
A.
A’
DANGER .
ANY ATTEMPT TO PUSH MATERIAL WITH ANYTHfNG
OTHER THAN THE DEBRfS TAMPER CAN RESULT IN
PERSONAL INJURY AND/OR MACHINE DAMAGE.
+
4
;.,’.
:,:.
‘.:
,. :::
,:.
293
To Next Page
Loading...
