Why won't my mcmurdo Smartfind M5 transponder power on?
If your mcmurdo Marine Radio transponder won't power on, there might be a few reasons: * There could be a faulty connection to the power source. Check the power connection to ensure it is secure. * The polarity might be reversed. Verify the power connection is correct. * The power supply current might be too low. Examine the power supply to ensure it meets the device's requirements.
What to do if my mcmurdo Smartfind M5 has no AIS transmission?
If your mcmurdo Marine Radio isn't transmitting AIS data, consider these potential causes: 1. The MMSI number may not be entered. You should enter the MMSI number in the settings. 2. The transmitter might be disabled. Make sure to enable the transmitter. 3. The power supply voltage could be too low. Check the power supply to ensure it's providing sufficient voltage.
How to fix mcmurdo Smartfind M5 Marine Radio with no GPS position data?
If your mcmurdo Marine Radio isn't showing any GPS position data, it might be due to an antenna or cabling problem. Check the antenna cable and its connections to ensure they are properly connected and in good condition.
Why does my mcmurdo Smartfind M5 AIS range seem too low?
If the AIS range on your mcmurdo Marine Radio seems too low, the issue might be with the VHF antenna and cabling. Check the VHF antenna and cable installation to ensure they are correctly installed and in good condition.
What to do if my mcmurdo Marine Radio has no picture on display?
If there is no picture on the display of your mcmurdo Marine Radio, here are a couple things to check: * Ensure the unit is powered up by pressing the power key. * The dimmer level might be set too low. Try increasing the dimmer level to see if the display becomes visible.
Why is my mcmurdo Smartfind M5 Marine Radio not showing any AIS target?
If your mcmurdo Marine Radio is not showing any AIS targets, the issue might be with the VHF cabling. Check the antenna cable and connections.
How to display map detail on mcmurdo Smartfind M5?
If there's no map detail showing on your mcmurdo Marine Radio, it could be that the coastline detail is not active. Try switching to coastline view to see if that resolves the issue.
What causes sensor ports not to respond on mcmurdo Smartfind M5?
If the sensor ports on your mcmurdo Marine Radio are not responding, the problem might be with the cable installation. Check the related wiring to ensure it is correctly installed.
What to do if the data port does not respond on mcmurdo Smartfind M5 Marine Radio?
If the data port on your mcmurdo Marine Radio is not responding, it may be due to the cable installation. Check the related wiring.
Information and illustrations are correct to the best of our knowledge. We reserve the right to change specifications without notice.
Covers electrical shock, RF radiation, power source, water contact, chemical solvents, and radio license warnings.
Details product category, compass safe distance, hardware/software version, type approval, FCC statement, disposal, and recycling info.
Instructions for servicing and contacting authorized service agents for the McMurdo Smartfind M5.
Overview of the McMurdo Smartfind M5 AIS Class A transponder, its components, and capabilities.
Highlights key features like compact design, compliance with standards, user-friendly GUI, and connectivity options.
Visual representation of how the Smartfind M5 connects to antennas, power, and other marine systems.
Lists all items included in the standard package for the Smartfind M5 AIS Transponder.
Step-by-step guide for installing the transponder unit, junction box, antennas, and connecting cables.
Specifies recommended RF cable types and connectors for VHF and GPS antennas.
Guidelines for optimal placement and installation of VHF and GPS antennas for performance.
Provides general guidelines and specific methods for mounting the transponder unit and junction box.
Details the connectors on the transponder main unit and junction box for various interfaces.
Covers connecting to power supply and initial setup steps, including MMSI programming.
Explains the functions of each button and display element on the transponder's front panel.
Describes various display modes like Coastal View, Radar View, and AIS Target List.
Instructions on how to use the knob for entering and editing text on the device.
Overview of the menu structure, how to access main and sub-menus, and brief descriptions of menu items.
Details how to send and receive Safety Related Messages (SRM), including Inbox, Outbox, Broadcast, Addressed, and Long Range types.
Covers specific inland message types like ETA/RTA, POB, EMMA warnings, and Water Level.
Provides info on Own Ship, AIS Targets, Region List, Alarms, Sensors, Dangerous Targets, MOB List, and Friend Ships.
Covers vessel info setup including Own Ship, Voyage, CPA/TCPA, MMSI/IMO/ENI, Retry Times, and AIS Mode.
Details specific settings for inland waterways, including Vessel Data, ETA, Number of Person, Blue Sign, and Report Rate.
Covers user preferences like Customize, Radar View, Map Calibration, Sensor Config, Factory, Password, Alarms, VSWR.
Explains various system tests for checking integrity, memory, ports, display, keyboard, GPS, communication, and version.
Lists international standards and resolutions that the Smartfind M5 complies with.
Technical specifications for the VHF transceiver, including frequency, bandwidth, modulation, and power output.
Technical specifications for the DSC receiver, including frequency, modulation, and sensitivity.
Specifications for the internal GPS receiver, including channel count, sensitivity, and position accuracy.
Details the required supply voltage and power consumption of the unit.
Specifications for the device's LCD display, including size, resolution, and dimmer control.
Description of the input controls, including the number of keypads and the multi-function knob.
Lists all available physical connection ports for antennas, sensors, and external devices.
Information on operating conditions, temperature range, humidity, and waterproof rating.
Provides the physical dimensions and weight of the transponder unit.
Details the specifications for the pilot plug, including cable length and connector type.
Lists supported NMEA 2000 Parameter Group Numbers (PGNs) for transmit and receive.
Detailed front and side view dimensions of the Smartfind M5 transponder main unit.
Provides the dimensions for the junction box unit.
Dimensions for accessories like extension cable, mounting template, GPS antenna, and pilot plug.
Describes the sensor input and bidirectional data ports conforming to IEC 61162-2 standard.
Details the presentation interface for the Smartfind M5, including sensor inputs and data outputs.
Lists the IEC 61162 data sentences supported for input and output.
Explains the format and meaning of various input AIS sentences like ABM, ACA, ACK, AIR.
Explains the format and meaning of various output AIS sentences like ABK, ACA, ALR, EPV, LR1.
Details alarms triggered by system failures and the corresponding reaction of the transponder.
Provides a template for recording installation details and maintenance history.
Information on tracking software versions and recording maintenance updates.
Guidance for US vessel owners on downloading the USCG AIS inspection checklist.
General| GPS | Yes |
|---|---|
| Operating Temperature | -20°C to +55°C |
| Floatation | Yes |
| Strobe Light | Yes |
| Frequency | 121.5 MHz (homing) |
| Battery Life | >24 hours |
| Activation | Manual |
| Battery Type | Lithium |
| Certification | COSPAS-SARSAT |
To Next Page
