McNeilus Street Smart Vision Extreme

Questions and Answers

F
fjacksonAug 16, 2025
What to do if McNeilus Monitor lights up but no picture appears?
- A
  Adam ConnerAug 16, 2025
  If your McNeilus Monitor lights up but doesn't display a picture, try these solutions: * Adjust the monitor controls (brightness, tint, etc.) to see if the picture appears. * Inspect the cable connections: remove any debris and ensure they are secure. If the cable is damaged, replace it. * Test the cable by plugging the camera directly into the monitor. If the camera works, the cable needs to be replaced. * Make sure the cable is plugged in correctly.
M
mark10Aug 19, 2025
Why is the picture on my McNeilus Monitor blurry and distorted?
- G
  George GardnerAug 19, 2025
  A blurry, out-of-focus, or distorted picture on your McNeilus Monitor can be due to several reasons: * **Dirty Camera Lens:** Clean any dirt, dust, or moisture from the outside of the lens cover. * **Incorrect Monitor Controls:** Adjust the monitor's brightness, tint, and other controls to see if the picture clears. * **Incorrect Video Composite Settings:** Ensure that both the OSD and DVR video composites are set correctly. For North and South America, use NTSC. For Europe, use PAL. * **Low Truck Battery Voltage:** If the truck battery voltage drops below 10V, the camera images may become distorted. Fully charge the battery and unplug, then plug back in the Power Accessory Harness to the bottom of the monitor to reset it.
D
davidnorrisAug 22, 2025
How to troubleshoot a McNeilus Street Smart Vision Extreme that does not power up?
- M
  Ms. Erica FullerAug 22, 2025
  If your McNeilus Monitor isn't powering up, check the following: * Verify power to the Battery/yellow wire and ACC power/red wire. * Inspect the fuses for the Battery and ACC power wires. If any fuses are bad, replace them with a standard 5 Amp Mini ATM fuse.
A
Amber GriffithAug 25, 2025
What to do if McNeilus Street Smart Vision Extreme screen is dark or blue?
- A
  Andrew NelsonAug 26, 2025
  If your McNeilus Monitor screen is dark or blue, even if cameras are not plugged in, follow these steps: 1. Check that the cameras are properly plugged in and detected by the monitor software. 2. Select the menu button until AUTO/NTSC appears in the upper left corner of the monitor. This AUTO function detects and recognizes the cameras being plugged in. 3. Check the cable by removing the camera from the cable and plugging the camera directly into the monitor. If the camera works, replace the cable. 4. Make sure the cable is plugged in correctly.
A
Andrew ButlerAug 28, 2025
Why does my McNeilus Monitor keep losing its settings?
- R
  Robert OrtizAug 28, 2025
  If your McNeilus Monitor is losing its settings, make sure the yellow wire of the Power Accessory Harness is plugged into the battery or a constant power source, and do not shut the battery power off.
S
Sherri PearsonAug 31, 2025
How to fix a McNeilus Street Smart Vision Extreme that is not displaying color?
- A
  Ashlee RamirezAug 31, 2025
  To resolve a McNeilus Monitor not displaying color, check the video composite settings. Ensure that both the OSD and DVR video composites are set to NTSC if you are in North or South America, or to PAL if you are in Europe.
R
Rita BrownSep 3, 2025
What to do if McNeilus Street Smart Vision Extreme does not recognize the SD card?
- Q
  qhillSep 3, 2025
  If your McNeilus Monitor isn't recognizing the SD card, try the following steps one at a time: 1. Ensure the card is correctly inserted into its port and pushed in all the way. 2. Power the monitor off, then turn it back on while keeping the SD Card installed. 3. Format the SD Card. 4. Replace the SD Card.
M
Mark GreenSep 6, 2025
How to adjust the camera viewing angle on a McNeilus Street Smart Vision Extreme?
- C
  Catherine GraySep 6, 2025
  If you're unable to achieve the correct camera viewing angle on your McNeilus Monitor: 1. Adjust the viewing angle of the camera more downward. 2. Reposition the camera bracket on the body of the truck to get a better angle. You may need to remove the camera bracket and camera from the truck, then remove the camera from the camera bracket. Rotate the bracket to give the camera a different position in the bracket. Replace the camera in the bracket and then replace the bracket on the truck.
B
Brandi LynchSep 9, 2025
What to do if I cannot access the DVR main menu on my McNeilus Street Smart Vision Extreme Monitor?
- N
  Nathaniel MartinSep 9, 2025
  If you're unable to access the DVR main menu on your McNeilus Monitor: 1. Enter the DVR through the OSD menu. 2. Select DVR Menu. The DVR main menu will display. If you still cannot access the DVR menu, you may need to remove the SD Card in order to stop the DVR recording. The DVR menu should now be accessible. After making necessary changes to the DVR options, reinsert the SD Card to start recording immediately. Refer to Troubleshooting item H, number 2 to determine if the DVR is recording.
C
Christian JonesSep 12, 2025
How to access the OSD menu on McNeilus Street Smart Vision Extreme Monitor?
- R
  Robert LopezSep 12, 2025
  To access the OSD menu on your McNeilus Monitor: 1. Press and hold the Menu button to enter the OSD menu. 2. If you are still unable to access the OSD menu, the monitor may be Passcode locked; refer to page 22 to unlock it.