Medline MDS400SA - User Manual

Questions and Answers

S
Steven ReynoldsAug 13, 2025
What to do if my Medline MDS400SA Lifting Systems lift will not operate even though battery indicator shows charge?
- M
  marcusyoderAug 13, 2025
  If your Medline Lifting System lift isn't working despite the battery indicator showing a charge, first, ensure the charger is unplugged. Then, check the connection between the control box and hand control, plugging it in firmly or replacing the hand control if needed. Also, ensure the actuator cord is securely plugged into the control box.
Y
Yvonne DavidsonAug 17, 2025
What to do if my Medline MDS400SA Lifting Systems lift will not operate and battery indicator has no lights illuminated?
- J
  Jimmy OrozcoAug 17, 2025
  If the battery indicator on your Medline Lifting System isn't illuminated and the lift won't operate, try these steps: First, make sure the red emergency stop button is in the “on” position by turning it until it pops up. Next, check inside the control box to ensure the batteries are properly connected. If that doesn't work, charge the batteries, again making sure the emergency stop is in the “on” position. If the batteries still won’t hold a charge, they likely need to be replaced.
F
Frank JeffersonAug 20, 2025
Why does the battery indicator on my Medline MDS400SA need frequent charging?
- L
  Linda LyonsAug 20, 2025
  If the battery indicator on your Medline Lifting System shows frequent charging needs or the lift loses power, it's likely that the internal batteries are at the end of their life cycle and should be replaced.
B
blopezAug 25, 2025
Why is my Medline Lifting Systems actuator making a grinding sound when lifting?
- R
  rbrownAug 25, 2025
  If your Medline Lifting System's actuator is making a grinding sound while lifting with a load, but works fine without it, the internal gear is likely stripped due to overloading. You should repair or replace the actuator.
T
Taylor TaylorAug 28, 2025
What to do if Medline MDS400SA actuator stops and starts during lifting or lowering?
- P
  Pamela WhiteAug 28, 2025
  If your Medline Lifting Systems actuator stops and starts during lifting or lowering, the batteries may be bad. Try replacing them.
S
Scott HaasSep 1, 2025
How to fix Medline MDS400SA when during charging the battery, indicator is not illuminated and won’t charge?
- C
  christina30Sep 1, 2025
  If the battery indicator on your Medline Lifting System charger isn't lit and the battery won't charge, first ensure the red emergency stop button is in the “on” position. If it still doesn't charge, inspect the charger for damage and replace it if necessary.
J
Jose DukeSep 4, 2025
Why does my Medline MDS400SA Lifting Systems actuator make a clicking sound when installed?
- R
  Robert ClarkSep 5, 2025
  If the actuator on your Medline Lifting System is installed and you hear a clicking sound, ensure the actuator plug is firmly plugged into the control box. If the sound persists, the actuator might be defective or at the end of its life cycle and may need replacement, assuming the control box is in good condition. Alternatively, the control box itself could be defective, requiring replacement of the PCB.
M
murphybenjaminSep 8, 2025
What to do if Medline Lifting Systems actuator will either go up or down, but not both?
- L
  Laura LopezSep 9, 2025
  If your Medline Lifting System actuator only goes up or down, but not both, the hand control or control box may be defective. Replace the PCB if the hand control is working. If the hand control is bad, replace it.

Medline MDS400SA Specifications

General

Brand	Medline
Model	MDS400SA
Category	Lifting Systems
Language	English

Medline MDS400SA - User Manual

Table of Contents

Questions and Answers

Medline MDS400SA Specifications