Melitta LOOK Timer User Manual

7
if they are supervised or instructed in how to
use the appliance safely and have understood
the dangers involved in using it.
•Childrenmustnotplaywiththeappliance.
•Replacingthepowercableandanyother
repairs should only be carried out by the
Melitta
®
customer service or by an
authorised repair workshop.
2. Before rst use:
•Ensurethatthepowersupplyinyourhome
corresponds to that on the model plate on the
base of the appliance.
•Connecttheappliancetoapowersource.Unused
cable can be stored in the base of the appliance. 
•Setthecurrenttimeusingthebuttons“h”and“m”
. This goes faster if you hold down the button.
The appliance is only ready to use once the
time has been set. You can turn the display light
on or o by simultaneously pressing the h and m
buttons  for longer than two seconds
•Allapplianceshavebeentestedduringproduction
to ensure they work perfectly. Therefore there may
be for example water deposits remaining. Rinse the
appliance twice with the maximum amount of water
and without a filter bag or ground coee, in order to
clean it.
•Forthebestcoeeenjoymentandconvenientuse,
the appliance is equipped with various features.
These features are explained below.
3. Set water hardness
Depending on water hardness lime scale may build up
in the appliance. This increases the appliance’s energy
consumption as lime scale on the heating element can
prevent the water heating eectively. To avoid damage
the appliance must be descaled regularly. The descaling
display helps you in this. If the CALC-button  is
permanently lit this shows that the appliance needs to
be descaled.
The appliance is pre-set for a high level of water
hardness (level 4). You can find out the level of water
hardness in your area by asking your local water
provider or by using water hardness measuring strips
available in the shops. For softer water the descaling
display can be adjusted to descale less often.
•HolddowntheCALC-button and by briefly
pressing the m-button  set the desired level of
water hardness. The hardness setting will then
show in the display
•Onceyouhavesetthedesiredlevelofwater
hardness, let go of the CALC-button.
Your settings are now saved.
•Thesettingsanddisplayareshowninthetable.
Hardness
setting
I II III IV
°dH
<7°
dH
7-14°
dH
14-21°
dH
>21°
dH
Display 
1
2 3 4
Please note:
•Waterhardnesscannotbeprogrammedwhilebrewing.
•Thelastwaterhardnesslevelchosenremainseven
after removing the power cable.
4. Setting the hotplate
Keeping coee warm on the hotplate aects the taste
of your coee. To avoid this you should enjoy your
coee fresh, by drinking it as soon after brewing as
possible. Unnecessary warming also uses valuable
energy. The factory settings for the appliance are for
40 minutes of warming. After this the hotplate turns
o automatically. This time can be changed as needed:
•HolddowntheSTART-button and by briefly
pressing the m-button  set the desired time
(20, 40 or 60 minutes). The current warming
time will be shown in the display .
•Onceyouhavesetthedesiredwarmingtime
let go of the button. Your setting is now saved.
•Thelastsettingchosenremainsevenafterremoving
the power cable.
5. Making coffee
•Ensurethattheapplianceisconnectedto
the power source.
•Openthelidonthewatertank.
•Fillthewatertankwiththedesiredamountofwater
using the glass pot. With the help of the water level
display on the tank  you can choose the correct
number of cups.
Smallcupsymbol=approx.85mlcoeepercup,
large cup symbol = approx. 125mlcoeepercup.
•Closethelidonthewatertankandplacetheglass
pot with closed lid in the appliance.
•Opentheswivellter to the left.
•FoldaMelitta
®
filter bag 1x4
®
at the embossed seam
and place it in the filter holder.  Press the filter bag
into the filter holder by hand, to ensure a good fit.
•Putthegroundcoeeintothelter.Theamount
depends on your personal taste. We recommend
using 6g of ground coee per large cup.
•Swivelthelterbackintotheappliance.
An audible click tells you it is inserted properly.
•WiththeMelitta
®
Aroma Selector  you can set
the taste of your coee with just one hand: From
mild-aromatic (
)to strong intensive ( ).
•Turntheapplianceon. Brewing begins.
•Aftermakingyourcoeethehotplatewillkeepit
warm and will turn o automatically after the time
you have set (see point 4). This avoids unnecessary
use of electricity and saves energy. You can of course
turn the machine o manually at any time.
•Thedripstoppreventsyourcoeefromdripping
when you remove the pot from the appliance. 
•Withthehelpofthedetachableinnerlteryoucan
dispose of the filter bag simply and easily.
6. Timer Feature
The appliance is equipped with a TIMER feature. This
starts the brewing process at a time you programme.
•Preparetheapplianceasdescribedinpoint5‘making
coee’, but without pressing the START button.
•Tosetthedesiredstarttime,holddowntheTIMER
button . The first time you programme it the
display will show 00:00.
G B

Melitta LOOK Timer Specifications

General

Timer	Yes
Control type	Buttons
Product color	Black, Transparent
Housing material	Stainless steel
Material	Glass
Number of jugs supported	1
Steam pipe	No
Product type	Drip coffee maker
Capacity in cups	15 cups
Coffee input type	Ground coffee
Coffee maker type	-
Appliance placement	Countertop
Reservoir for brewed coffee	Jug