To Next PageTo Next PageWhy won't my Metabo HPT Impact Driver run?
If your Metabo HPT Impact Driver isn't running, it could be due to a depleted battery. Try charging the battery. Alternatively, the safety function might be activated if the switch trigger was held down when the battery was inserted. Release the switch trigger and pull it again to resolve this.
What to do if my Metabo HPT WH 18DDX battery will not charge?
If the Metabo HPT Impact Driver battery won't charge, ensure it's properly inserted into the charger until the red charge status lamp appears. Check that the charger is plugged into a working outlet. If the battery temperature is too hot or too cold, remove it from the charger and allow it to cool down or warm up to above 32°F (0°C).
Why did my Metabo HPT Impact Driver suddenly stop?
If your Metabo HPT Impact Driver suddenly stopped, it might be overburdened; eliminate the cause of the overburden. Another reason could be an overheated battery, in which case you should let the battery cool down. Also, the tool automatically stops if the switch trigger is held down for 5 minutes or more to prevent tool failure.
How to prevent screw head from slipping with Metabo HPT WH 18DDX Impact Driver?
If the screw head slips or comes loose when using the Metabo HPT Impact Driver, ensure the bit number matches the screw size by installing a suitable bit. If the bit is worn, replace it with a new one.
Why do my tool bits fall off my Metabo HPT WH 18DDX Impact Driver?
If tool bits can't be attached to or fall off of your Metabo HPT Impact Driver, it may be that the shape of the attachment portion doesn’t match. Use a bit with a hexagonal shaft that has a width across flats of 6.35 mm. If you are using an L-type tool bit, replace it with an S-type bit.
What to do if the switch can’t be pulled on Metabo HPT WH 18DDX?
If the switch of your Metabo HPT Impact Driver can’t be pulled, it might be because the forward/reverse selector button is positioned halfway. Press the button firmly into position for the desired direction of rotation.
Why does my Metabo HPT WH 18DDX Impact Driver make a high-pitched noise?
If you hear an abnormal high-pitched noise when the switch trigger is pulled on your Metabo HPT Impact Driver, it's likely because the switch trigger is only being pulled slightly. This is not a malfunction and won't occur if the switch trigger is pulled more fully.
General| Brand | Metabo HPT |
|---|---|
| Model | WH 18DDX |
| Category | Impact Driver |
| Language | English |
Defines signal words used in the manual for hazard identification.
Guidelines for maintaining a safe and organized work environment.
Precautions related to electrical hazards and proper tool grounding.
Advice on staying alert, using protective equipment, and preventing accidents.
Guidelines for proper operation, maintenance, and storage of power tools.
Instructions for safe handling and charging of battery-powered tools.
Detailed safety rules and explanations of symbols for tool operation.
Explains the meaning of various symbols found on the tool and in the manual.
Key safety directives specific to the cordless impact driver.
Essential safety guidelines for operating the battery charger.
Safety guidelines for using the battery and charger together.
Precautions for safely transporting lithium-ion batteries.
Identifies and illustrates the main components of the tool and accessories.
Lists the intended uses and tasks for the tool.
Step-by-step guide for battery removal and installation.
Instructions on how to charge the battery using the charger.
Information on battery temperature and recharging guidelines.
Tips and advice for maximizing battery lifespan and performance.
Procedure for inserting and securing the driver bit into the tool.
Procedure for safely removing the driver bit from the tool.
Explanation of how to operate the power tool's variable speed switch.
Guide to using the tool for tightening and loosening screws effectively.
Instructions for tightening and loosening nuts and bolts with the tool.
Explains the function and usage of the tool's integrated LED light.
Guide on how to attach and use the optional hook for portability.
Explains LED signals indicating tool protection functions and errors.
Important notes and precautions for continuous and optimal tool operation.
Instructions for inspecting and maintaining drill bits for optimal performance.
Importance of regularly inspecting and tightening screws on the tool.
Guidance on caring for the motor unit to prevent damage.
How to clean dust from the tool using appropriate methods.
Checking terminals for swarf and dust to prevent malfunction.
Information on the proper and safe disposal of used batteries.
Guidelines for storing the tool and batteries safely.
Information on where and how to get the tool serviced or repaired.
Lists and illustrates the accessories included with the tool.
Lists and describes accessories available for separate purchase.
