What to do if Metek Powervar Security II overload LED is illuminated and alarm sounds?
If the Overload LEDs are lit and you hear a continuous alarm, it means your Metek UPS is overloaded. To fix this, reduce the load by unplugging non-essential devices from the UPS.
Why is the Metek UPS backup time less than expected?
If the backup time of your Metek UPS is shorter than expected, it could be due to a battery that isn't fully charged or is dead. Recharge the battery for at least six hours and then test the backup time again.
How to fix a Metek UPS that does not power up?
If your Metek UPS isn't powering on and there's no alarm, here's what to check: 1. Ensure you press and hold the On/Off switch for at least 3 seconds. 2. Verify the wall socket has the correct line voltage. 3. Confirm the UPS input power cord is securely plugged in. 4. Check the rear panel circuit breaker; if tripped, reduce the connected load and reset it.
What to do if the Metek Powervar Security II UPS Low/Replace Battery LED is on?
If the Low/Replace Battery LED is lit on your Metek UPS, it indicates the battery voltage is too low or the battery is dead. Recharge the battery for at least six hours and then reset the UPS. If the LED remains on, you'll need to replace the battery.
What does it mean when the Site Wiring Fault LED is illuminated on Metek UPS?
If the Site Wiring Fault LED is illuminated on your Metek UPS, it indicates a problem with the site's wiring. Contact a qualified electrician to inspect and correct the wiring.
What to do if Metek UPS is normal, but the computer will not turn on?
If your Metek UPS appears to be working correctly, but your computer won't turn on, the computer's power cord may be loose or disconnected. Ensure the computer's power cord is properly connected.
Instructions for registering your AMETEK Powervar product purchase online.
Details risks associated with batteries and proper handling during replacement.
Defines the intended applications and usage guidelines for the UPM.
Guide on how to inspect the UPM for shipping damage.
Step-by-step instructions for quickly setting up and starting the UPM.
Detailed steps for safely unpacking and placing the UPM in a suitable environment.
Instructions on how to connect and apply power to the UPM.
Explains the UPM's front panel display and unit status indicators.
Procedures for performing an initial test of the UPM backup function.
Lists UPM status codes and their definitions for identifying issues.
Details the functions of the On/Off and Test/Silence buttons.
Describes the LED displays for load and battery charge status.
Explains the SF indicator and its meaning for improper wiring.
Details scenarios for automated system shutdown using software options.
Explains how to monitor UPM health via network systems.
Details monitoring scenarios using SNMP, BMS, or CIO software.
Describes PDU features for socket control, load shedding, and sequenced start-up.
Explains configuring automated turn-off of specific socket groups for load shedding.
How to configure restart delays for staged startup and automated startup after power recovery.
Steps to start the UPM using Start Manager when AC power is unavailable.
Guidelines for storing the UPM and its battery to maintain condition.
Details on battery type, lifespan, indicators, and important information.
Instructions and information for user battery replacement in non-medical units.
Detailed, step-by-step instructions for replacing the UPM batteries.
Warnings and cautions for servicing batteries, emphasizing user-serviceable parts.
Safety warnings related to battery replacement, including explosion risk and electrical hazards.
Technical specifications for North American models ABCE422-11 and ABCE422-11MED.
Technical specifications for North American models ABCE602-11 and ABCE602-11MED.
Technical specifications for North American models ABCE802-11 and ABCE802-11MED.
Technical specifications for North American models ABCE1102-11 and ABCE1102-11MED.
Technical specifications for North American models ABCE1442-11 and ABCE1442-11MED.
Technical specifications for North American models ABCE2202-11 and ABCE3002-11.
Technical specifications for International models ABCE422-22 and ABCE422-22MED.
Technical specifications for International models ABCE602-22 and ABCE602-22MED.
Technical specifications for International models ABCE802-22 and ABCE802-22MED.
Technical specifications for International models ABCE1102-22 and ABCE1102-22MED.
Technical specifications for International models ABCE1442-22 and ABCE1442-22MED.
Technical specifications for International models ABCE2202-22 and ABCE3002-22MED.
Provides solutions for common problems encountered with the UPM.
Lists the fuse ratings required for different UPM models.
Contact details and hours for AMETEK Powervar technical product support.
Details the warranty period for chassis, components, and batteries.
Warning against using UPM products with life support equipment.
To Next Page
General