MG MGA series User Manual

Details on locating and identifying car and engine numbers for correspondence.

Explains how to lock and unlock doors on the coupé model using the ignition key.

Details the operation of the hand brake lever for rear wheel brakes.

Advises against resting feet on the clutch pedal to prevent wear.

Describes engagement of gears, including reverse, and synchromesh.

Explains the foot-operated switch for dipping and raising headlamp beams.

Details the speedometer's functions for speed, trip, and total distances.

Explains the tachometer dial and its operating ranges.

Describes the warning light indicating dynamo charging status.

Indicates the cooling water temperature leaving the cylinder head.

Operation of the starter motor via the pull-out knob.

How to operate sidelamps, tail lamps, and headlamps.

Illuminating and dimming dashboard instruments.

Operation of wipers and their self-parking feature.

Function of the lever-type switch for flashing indicators.

Enriching mixture for starting and normal running position.

Operation and function as master switch.

Details operation of the heater and demister controls for air, demist, and temperature.

Operation of the washing equipment by pumping a knob.

Location of fluid storage and refill procedure.

Procedure for opening the fuel filler cap and checking fuel level.

Steps to release the safety catch after opening the bonnet.

Procedure for filling the radiator and caution for hot engines.

How to check engine oil level using the dipstick.

Procedure for adding engine oil via the filler cap.

Importance of checking tyre pressures weekly.

Steps for starting the engine, including mixture control and starter.

Procedure for warming the engine quickly to working temperature.

Recommended speeds for the first 200 miles to ensure proper break-in.

Advice on changing gears, braking, and anticipating traffic.

Instructions for accessing the boot via the seat and prop.

Location of the starting handle and tool kit.

Location and maintenance of the spare wheel.

Procedure for safely jacking up the front of the car.

Procedure for safely jacking up the rear of the car.

Steps for removing and refitting wheel discs.

Instructions for removing pressed steel wheels.

Procedure for removing wire wheels, noting thread direction.

Detailed steps for removing tyre covers from the rim.

Technique for fitting new tyres onto the rim.

Recommendation for vulcanized repairs over patches.

Instructions for checking valve operation and replacement.

Importance of keeping valve caps tight and clean.

Advice on tyre rotation, inspection, and alignment.

Checking spoke tension, spoke replacement, and rim inspection.

Description of attachment and operation of sidescreens.

Instructions for stowing sidescreens in the container.

Procedure for lowering the hood from the windshield.

Steps for correctly folding the hood when dry.

Guidance on washing, drying, and polishing the car's body.

Cleaning the windshield and avoiding detrimental polishes.

Cleaning instructions for car upholstery.

Cleaning the hood cloth with water and mild detergents.

Note on avoiding radiator muffs and using blinds.

Advice on using ethylene glycol or glycerine antifreeze.

Procedure for draining water from the engine block.

Procedure for draining the radiator using its drain tap.

Notes on draining the heater unit and using antifreeze.

Recommendations for engine oil based on climate conditions.

Maintenance tasks for every 3,000 miles service.

Maintenance tasks for every 6,000 miles service.

Greasing instructions for steering gear components.

Lubrication of universal joints and sliding joint.

Checking and replenishing gearbox oil level every 1,000 miles.

Explanation of fuse connections for accessories and ignition.

Guidance on using correct replacement fuses.

Method to free a jammed starter pinion.

Steps for removing and refitting light units for bulb replacement.

Procedure for replacing headlamp bulbs.

Instructions for repositioning wiper blades and fitting new rubber.

Procedure for adjusting headlamp beams according to regulations.

How to access and replace pilot lamp bulbs.

Operation and bulb replacement for the number-plate lamp.

Accessing and replacing bulbs in tail and stop lamps.

Locations of instrument panel lamps and warning lights.

How to find the TDC position using the crankshaft pulley.

Adjusting distributor timing using vacuum and centrifugal mechanisms.

Procedure for checking and adjusting valve clearances when hot.

General instructions for adjusting brakes.

Procedure for adjusting front brake shoes.

Procedure for adjusting rear brake shoes and hand brake.

Steps for adjusting carburetter jets for even idling and performance.

Setting slow-running by adjusting carburetter throttle stop screws.

Adjusting the linkage between mixture control and throttles.

Details of the complimentary inspection and service at 500 miles.

Maintenance tasks to be performed at 1,000-mile intervals.

Maintenance tasks for every 3,000 miles service.

Maintenance tasks for every 6,000 miles service.

Maintenance tasks for 10,000 miles service, with engine addition.

Maintenance tasks for 12,000 miles service.

Maintenance tasks for 24,000 miles service.

Checking and replenishing rear axle oil level.

Checking and topping up brake and clutch master cylinder fluid.

Lubricating carburetter piston dampers.

Checking electrolyte level and specific gravity.

Interpreting electrolyte specific gravity readings for battery status.

Greasing the hand brake cable nipple.

Procedure for draining engine sump oil and refilling.

Cleaning and re-oiling the air cleaner element.

Lubricating the dynamo rear end bearing plate.

Lubricating the distributor cam bearing.

Lubricating the distributor cam.

Adding oil to the contact breaker base.

Lubricating the moving contact pivot pin.

Inspecting and adjusting the dynamo driving belt.

Cleaning distributor contacts with abrasive stone or emery-cloth.

Checking and adjusting the contact breaker gap.

Cleaning and adjusting sparking plugs every 5,000 miles.

Procedure for draining and refilling the gearbox oil.

Procedure for draining and refilling the rear axle oil.

Lubricating front wheel hubs and repacking with grease.

Procedure for renewing the engine oil filter element.

Cleaning carburetter fuel filters.

Cleaning the fuel pump filter.

Cleaning damper bodies and topping up with fluid.

Importance of correct alignment for tyre wear.

Lubricating the water pump sparingly.

Cleaning rear damper bodies and topping up with fluid.

Lubricating steering gearbox and pinion nipples.

Procedure for flushing the engine oil system.

Points regarding warranty, claims, preventive maintenance, and parts.