MG TV User Manual

MG CO., LTD. www.mgco.jp
5-2-55 Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
BEFORE USE ....
Thank you for choosing us. Before use, please check con-
tents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact our sales office or representatives.
■ PACKAGE INCLUDES:
Signal conditioner ...............................................................(1)
■ MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■ GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +60°C
(23 to 140°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
EURO Type
Terminals
ZERO
SPAN
Body
Specifications/
Connection Diagram
Zero Adj.
Span Adj.
INSTALLATION
■ DIN RAIL MOUNTING
Set the unit so that its DIN rail adaptor is at the bottom.
Hang the upper hook at the rear side of the unit on the DIN
rail and push in the lower. When removing the unit, push
down the DIN rail adaptor utilizing a minus screwdriver
and pull.
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
■ WALL MOUNTING
Refer to “EXTERNAL DIMENSIONS.”
SIGNAL TRANSMITTER
(non-isolated)
MODEL
TV
EM-3317 Rev.6 P. 1 / 3
INSTRUCTION MANUAL

MG TV Specifications

General

Brand	MG
Model	TV
Category	Transmitter
Language	English

Summary

Before Use and Package Contents

Package Includes

Lists the items included in the signal conditioner package.

Model Number Confirmation

Confirms the model number marking on the product matches the order.

Points of Caution

General Precautions

Safety measures before removing or mounting the unit, including power and signal safety.

Environmental Considerations

Guidelines for indoor use, dust, vibration, temperature, and humidity for optimal operation.

Wiring Safety

Instructions for safe wiring, avoiding noise sources and bundling cables.

Operational Warm-up

Notes that a 10-minute warm-up period is required for complete performance.

Component Identification and Installation

Component Identification

Identifies key components of the signal transmitter, such as body, adjusters, and terminals.

DIN Rail Mounting

Describes the procedure for mounting the unit onto a standard 35mm DIN rail.

Wall Mounting

Refers to external dimensions for wall mounting instructions.

Terminal Connections and Wiring

Terminal Connections Overview

Instructions for connecting the unit, emphasizing not to interconnect negative sides of input/output terminals.

External Dimensions

Provides physical dimensions of the unit in millimeters and inches.

Connection Diagram

Illustrates the wiring diagram for input, output, and monitor terminals.

Wiring Instructions and Checking

Euro Type Terminal Wiring

Specifies applicable wire size and stripped length for Euro type terminals.

Wiring and Input/Output Checking

Steps to verify terminal wiring, input voltage, and output load.

Maintenance and Adjustment

Calibration Procedure

Details regular calibration by applying various input signals and checking output.

Lightning Surge Protection

Information on surge protectors for protection against lightning-induced surges.

Output Signal Calibration

Procedure for matching the signal to a receiving instrument or for regular calibration.