DIGITAL POWER SOURCE (D.P.S) FEATURES
This MICHELIN tyre inflator incorporates a 5V USB port.
USB PORT
Under the right hand cover is a single 5V USB port (4) suitable for charging mobile phones with a
maximum rating of 0.5A.
TYRE INFLATION:
1. With the On/Off button (1) in Off position, unwind power cord and plug the small end into the input
(6) and the 12V power plug into your vehicle’s 12V power plug socket. Wait a few seconds until
digital display shows zero. Please note - when the On/Off button is in the Off position, it protrudes
from the unit slightly. When in the On position the button is flush to the unit.
2. Press the PSI, BAR & kPa button (5) to select desired pressure format.
PSI
12V POWER PLUG
TO REPLACE FUSE IN 12V PLUG:
Undo knurled ring anti-clockwise
TROUBLE SHOOTING
OTHER MICHELIN PRODUCTS AVAILABLE:
TYRE INFLATORS FOOTPUMPS DIGITAL TYRE CAR MATS
PRESSURE
GAUGES
kPa BAR
Lift up the high pressure hose and screw the tyre valve connector (3) onto the tyre valve. Always
connect the 12V power plug before connecting the high pressure hose to the tyre. Check the tyre
pressure shown on the display. If the display reads 0.00 or Err then refer to the Trouble Shooting
guide. When connected correctly the gauge will display the current pressure in the tyre. If this is the
pressure as stated in your vehicle’s handbook, you can simply remove the tyre valve connector (3).
3. To start inflating press On/Off button (1).
4. You will now see the pressure increasing on the display (2). Due to the sensitive nature of the tyre
pressure measuring system, you may find that when you switch the tyre inflator off at the required
pressure the gauge may drop back slightly. If this happens, switch back on and inflate to a slightly
higher pressure. Switch off and re-check.
5. If you are inflating multiple tyres then follow the procedure stated from 3. to 4. above.
If the 12V power supply is disconnected then always reconnect the 12V power supply before
connecting the high pressure hose to the tyre valve. If there is a power interruption during the
inflation cycle, please follow the reset procedure outlined in the Trouble Shooting guide.
Gauge does not illuminate
Unit fails to run with switch in ‘On’ position
Power lead/plug becomes hot
Gauge appears to read incorrectly or
is unreadable
Gauge reads 0.0 or ERR
Unit is running but tyre is not inflating
Gauge does not display when tyre valve
is connected
Check that plug is fully inserted into 12V socket
Check internal plug fuse (10A glass type).
Your car may require the ignition key to be
turned to the accessory position.
If power lead is coiled, uncoil to full length.
Ensure 12V socket is clean with no debris in it.
Ensure 12V plug components are tight and clean.
When the tyre valve connector is attached,
before switching the unit on, ensure the gauge
is reading your current tyre pressure.
Disconnect valve connector from the tyre.
Remove plug from power source for at
least 5 seconds, reconnect to power.
Press and hold yellow reset button until
display shows all the digits then returns to
0.0. Connect valve connector to tyre.
Check that the tyre valve connector is
correctly fitted to tyre valve.
Ensure tyre valve is correctly connected to the
tyre valve connector
Customer enquiries:
We’re at your service. Let us help
you, find a better way forward.
Customer enquiries UK & ROI:
+44 (0)800 731 4973
michelinhelpline@caeurope.co.uk
International Customer enquiries:
www.michelin-lifestyle.com
MICHELIN and/or the Michelin Man Device and/or BIBENDUM are trademark(s) owned by, and used with
the permission of, the Michelin Group. © 2019 Michelin
Manufactured and distributed under license in the UK & ROI by
Custom Accessories Europe Ltd., Berkshire, RG17 0RB, UK.
International distribution by ML Direct Ltd, 224 Queensferry Rd, Edinburgh, EH4 2BN, UK
For all other issues please call the helpline: +44 (0)800 731 4973
To Previous Page
Loading...
Need help?
General
