Why is the breakaway arm loose and not returning to stop on my Micron Spraydome Tank Equipment?
If the breakaway arm is loose and doesn't return to stop, the return spring is either detached or broken. Reattach or replace the spring.
Why is the flow rate low or varying in my Micron Tank Equipment?
A low or varying flow rate could be due to several reasons: the tank level may be low or empty, the nozzle or filter may be partially blocked, the hose could be blocked or kinked, the supply pressure might be too low, the pump could be faulty, there might be air in the system, or the spray fluid may be aerated. Refill the tank, clean the nozzle and filters, purge and straighten the hoses, increase the supply pressure to between 1 and 2 bar, replace the pump, purge air from the system, or reduce pump operation or agitation.
How to troubleshoot Micron Spraydome Tank Equipment when pump and CDA atomiser are not operating?
If the pump and CDA atomiser are not operating, the inline switch might be off, the fuse might be blown, or there could be a loose connection at the battery or backplate, or incorrect wiring. Switch on the inline switch and controller, check the system and replace the fuse, check all connections and tighten as necessary, and check the wiring and rewire as necessary.
What to do if Micron Spraydome Tank Equipment pump will not operate?
If the pump won't operate, it could be due to several reasons: the pump wire might not be connected to the backplate, there might be a loose electrical connection, the diode might be faulty, the diode polarity might be incorrect, the pump motor might be faulty, or the wiring might be incorrect. Connect the pump wire to the backplate 2 pin panel socket, check all connections and tighten as necessary, replace the diode, reverse the diode connections, replace the pump motor, or check the wiring and rewire as necessary.
What causes a high flow rate in Micron Tank Equipment?
A high flow rate can be caused by an incorrect or worn nozzle or a supply pressure that is too high. Replace the nozzle with a new one and reduce the supply pressure to between 1 and 2 bar.
What causes Micron Tank Equipment CDA atomiser not to spin and lamp not to glow?
If the CDA atomiser doesn't spin and the lamp doesn't glow, the unit might be switched off, the fuse might be blown, the motor might be faulty, there might be a broken wire or loose connection, a corroded terminal, a blown globe, a loose globe, an incorrect wattage globe, or incorrect wiring. Switch on the inline switch and controller, check the system and replace the fuse, replace the motor, check the wiring, check and tighten the connections, clean or replace the terminal, replace the globe, adjust the globe holder, replace the globe, or check the wiring and rewire as necessary.
How to fix a stiff breakaway arm on Micron Spraydome?
If the breakaway arm is stiff or does not move, the pivot may have seized. Dismantle, clean and lubricate the pivot.
Why is the green wire in my Micron Spraydome control unit overheating or melting?
If the green wire in the control unit is overheating or melting, the battery polarity is likely incorrect. Replace the green wire and reverse the battery connections.
What to do if Micron Spraydome Tank Equipment CDA spins too fast and lamp does not glow?
If the CDA spins too fast and the lamp doesn't glow, it's likely due to an incorrect wattage globe or reversed globe wiring. Replace the globe and check and rewire the globe wiring.
Why is the CDA spinning slowly on my Micron Spraydome Tank Equipment?
If the CDA spins slowly, it could be due to moisture or corrosion in the motor, or an incorrect wattage globe. Replace the motor or the globe.
Provides detailed specifications for the equipment.
Lists critical warnings and prohibitions for safe operation.
Details mechanical risks and low voltage electrical safety.
Specifies PPE requirements for operators.
Outlines safe practices when handling and using pesticides.
Guidelines for environmentally responsible disposal and practices.
Details methods and ratings for reducing spray drift.
Step-by-step guide for the initial assembly of specific models.
Procedures for setting the correct output flow rate for atomisers and nozzles.
Steps for preparing the spray mix, including safety and tank filling.
Lists common mechanical problems and their solutions.
Troubleshooting specific issues with Hi-Flo spray heads.
Troubleshooting specific issues with CDA equipment.
General| Brand | Micron |
|---|---|
| Model | Spraydome Series |
| Category | Tank Equipment |
| Language | English |
To Next Page
