MikroTik CSS610-8G-2S+IN User Manual

1.
2.
3.
CSS610-8G-2S+IN
CSS610-8G-2S+IN
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.
It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling
requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.
Quick start
Download the latest SwitchOS software version fromhttps://mikrotik.com/download;
Connect your computer to any of the ethernet ports;
Connect the device to the power source;
Set an IP address of your computer to 192.168.88.3;
Open your Web browser, the default management IP address is 192.168.88.1 / 192.168.88.2, with the username and no password; admin 
Upload file with the web browser to the Upgrade tab, the device will reboot after an upgrade;
Set up your password to secure the device.
Powering
The device accepts power from the power jack or from the first Ethernet port (Passive PoE).
Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 12-57V DC.
The first Ethernet port accepts passive PoE input 12-57V DC.
Power consumption 5 W, with attachments 11 W.
Connecting to a PoE Adapter:
Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.
Connect an Ethernet cable from your local network (LAN) to the PoE adapter.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
Configuration
SwOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the
possibilities:https://mt.lv/help.
For recovery purposes, it is possible to boot the device for reinstallation, see sectionButtons and Jumpers.
First-time configuration https://wiki.mikrotik.com/wiki/SwOS/CSS610;

MikroTik CSS610-8G-2S+IN Specifications

General

Switch type	-
SFP+ module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
10G support	Yes
MAC address table	- entries
Product color	White
DC input voltage	12 - 57 V
Power consumption (max)	11 W
Operating temperature (T-T)	-20 - 60 °C

Weight and Dimensions

Depth	167 mm
Width	200 mm
Height	46 mm

Summary

Safety Warnings

General Safety Precautions

General safety guidelines for working with electrical equipment, installation, and product usage.

Customer Responsibility

Customer's responsibility for local regulations and professional installation.

Quick Start Guide

Initial Setup Steps

Steps for downloading software, connecting the device, setting IP, and accessing via web browser.

Powering Options

Power Input Methods

Describes power input via direct power jack or passive PoE.

Connecting to PoE Adapter

Step-by-step guide for connecting the device using a PoE adapter.

Device Configuration

Configuration Resources

Links to resources for SwOS configuration and recovery procedures.

Ports and Connectivity

Ethernet and SFP+ Ports

Details on eight Gigabit Ethernet ports and two SFP+ ports for 10G SFP+.

Technical Specifications

SFP Module Compatibility

Link to SFP module compatibility table for reference.

Mounting Instructions

Rackmount and Desktop Installation

Instructions for attaching rack ears and placing the device in a rackmount.

Environmental Considerations

Guidance on placement in a dry, ventilated environment and cable recommendations.

Buttons and Jumpers

Reset and Reinstallation

Describes button function for resetting configuration and loading backup software.

Operating System

Supported OS

Confirms SwOS as the only supported operating system for the device.

FCC Compliance

FCC Interference Statement

Statement regarding FCC rules, interference limits, and user responsibilities.

Innovation, Science and Economic Development Canada Compliance

Canadian Compliance Statement

Statement regarding compliance with Canadian license-exempt transmitter/receiver regulations.

UKCA Marking

UKCA Mark Information

Indicates compliance with UK conformity standards.

Eurasian Conformity Mark (EAC)

EAC Mark Information

Explains how to interpret the manufacturing date from the serial number and EAC mark.

Norma Oficial Mexicana (NOM) Compliance

NOM Energy Efficiency

Statement on compliance with NOM-029-ENER-2017 for energy efficiency.

CE Declaration of Conformity

EU Declaration of Conformity

Provides the internet address for the full text of the EU Declaration of Conformity.