Millarco Mi Lock 25.804 - Safety Instructions; Opening the Safe for the First Time; Installing the Batteries; Programming the Code

   Udvendigemål
  Højde  Bredde  Dybde
Model25.806-SFT-20ENP  200mm. 310mm. 200mm.
Model25.800-SFT-25ENP  250mm. 350mm. 250mm.
Model25.802-SFT-30ENP  200mm. 380mm. 300mm.
Model25.804-SFT-503530EN 500mm. 350mm. 300mm.
Model25.808-SFT-35EN  205mm. 450mm. 3850mm.
Digitalkodelås
Bruger4xAAbatterier
(medfølgerikke)
Stedogdato:
Lystrup,22.marts2013
Signeret:LarsBærentsen
DK-8520Lystrup
www.millarco.dk
Vitilbydergarantipåvoresprodukterioverensstemmelsemedgældende
lovgivningidetenkelteland.(Købsbevisskalforelægges).
Vitilbydergratisreparationerigarantiperiodenioverensstemmelsemed
Købelovenogihenholdtilfølgendevilkår.
1.Fejlenerenmaterielellerdesignmæssigfejl(detteomfatterikke
almindeligslidellerforkertanvendelseafproduktet).
2.Dererikkeudførtreparationerellerforsøgpåreparationerafandre
endMillarcosautoriseredeværksteder
3.Ingenikke-originaledelebrugesmedproduktet
Gratisservicedækkerudskiftningafdefektedelesamtarbejdstid.
Produktetskalaeveresvedforhandleren,dersenderdetvideretilreparation.
Vimodtagerikkeprodukter,somfremsendestilosigarantiperiodendirektefra
kunden.
Hvisduhartekniskespørgsmål,erduvelkommentilatkontaktevores
serviceværksted:
MillarcoInternationalA/S,Rokhøj26,DK-8520Lystrup
Servicetelefon:+4587434233
E-mail:service@millarco.dk
 Service&reparation
Tekniskespecikationer
Toopenthesafeforthersttime,removethesmallcentralrubbercover“Z”
(seediagram2)betweenknobandkeypad,insertthekeyintothelockandturnit
counter-clockwise,atthesametime,turnthedoorknobclockwiseandopenthe
door.
Thesaferequires4xsize“AA”(1.5V)batteries.
Thebatteriescompartment“Y”(seediagram1)islocatedonthebackofthe
door.Removethebatterycoverandinstallthebatteriesintothecompartment.
Ensurethebatteriesarettedwiththecorrectcorrespondingpolarity.
Oncethebatteriesareinstalled,closethebatterycompartment.
A. Removethebatterycoverandpresstheredbutton“X”insidethebattery
 compartment(seediagram1),releaseitandyouwillheartwobeeps.
B. Nowpressfrom3to8numbersthatyouwishtouseasacombination,
 andconrmbypressingtheletter“B”within5seconds.Oryouhavetodo
 fromthebeginning.
C. Writedownyournewcombinationimmediatelyandcheckwhetheryournew
 combinationhasbeenprogrammedornotonconditionsofthesafe
 dooropen.
Toopenthesafe,enteryourpersonalcodeandconrmbypressingtheletter
“A”.Youwillhearabeepandthegreenlightwillbeon,thenopenthedoorusing
theknobwithin5seconds.
Ifyouoranintruderusestheincorrectgroupofnumbers,itwillnotopen.If
theincorrectcombinationisused3timesconsecutively,youmustwaitfor20
secondsbeforereattempting.Ifagaintheincorrectcombinationisselected3
times,youmustwaitapproximately5minutesbeforereattemptingaccess.
minutterindenduprøverigen.
 1.OPENINGTHESAFEFORTHEFIRSTTIME
 2.INSTALLINGTHEBATTERIES
 3.PROGRAMMINGTHECODE
 4.USINGYOURSAFE
 SafetyInstructions
Thankyouforpurchasingthisprodcut.Toobtainsatisfactoryresults,pleaseread
carefullythroughthismanual.Alwayskeepthemanualtogetherwiththeproduct.
CAUTION:Donotkeepthekeysinthesafeitself.
UK-UserManual