Milwaukee AGV 24-230 E - Technical Data

22 ENGLISH
TECHNICAL DATA AG 24-230E AGV 24-230E AGV 26-230 GE
Angle Grinder AGV 24-230 GE
Production code 4026 15 04...
4026 57 04...
4768 20 02...
4768 35 02...
...000001-999999
4026 21 04...
4026 18 04...
4026 69 04...
4768 48 02...
4768 59 02...
4768 98 02...
...000001-999999
4026 53 04...
4026 65 04...
4769 08 02...
4769 10 02...
...000001-999999
Rated input 2400 W 2400 W 2600 W
Rated speed 6600 min
-1
6600 min
-1
6600 min
-1
D=Grinding disk diameter max.
d=Grinding disk hole diameter
230 mm
22,2 mm
230 mm
22,2 mm
230 mm
22,2 mm
b=Grinding disk thickness max.. 6 mm (1/4") 6 mm (1/4") 6 mm (1/4")
b=Cutting disk thickness min. / max.
1,9 / 3 mm 1,9 / 3 mm 1,9 / 3 mm
D=Grinding surface diameter max.
230 mm 230 mm 230 mm
D=Wiring brush diameter max. 100 mm 100 mm 100 mm
Thread of work spindle M14 M14 M14
Weight according EPTA-Procedure 01/2014 5,3 kg 5,5 kg 5,5 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) 93 dB(A) 93 dB(A) 93 dB(A)
Sound power level
(Uncertainty K=3dB(A))
104 dB(A) 104 dB(A) 104 dB(A)
Wear ear protectors!
Vibration total values (triaxial vector sum) determined
according to EN 60745.
Surface grinding:
Vibration emission value a
h,SG
6,0 m/s
2
2,7 m/s
2
2,7 m/s
2
Uncertainty K 1,5 m/s
2
1,5 m/s
2
1,5 m/s
2
Sanding
Vibration emission value a
h, DS
< 2,5 m/s
2
< 2,5 m/s
2
< 2,5 m/s
2
Uncertainty K 1,5 m/s
2
1,5 m/s
2
1,5 m/s
2
For other applications, e.g. Abrasive Cutting-O󰀨 Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di󰀨 erent
applications, with di󰀨 erent accessories or poorly maintained, the vibration emission may di󰀨 er. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o󰀨 or when it
is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e󰀨 ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns