LIGHT
Use and charge only REDLITHIUM™ USB batteries in
this USB rechargeable light. Other types of batteries may
cause personal injury and damage.
Inserting the Battery
1. Twist the cap and remove.
2. Line up the battery with the compartment and fully insert the battery.
3. Replace the cap and twist to secure.
Charging the Battery
1. Plug your USB cable into a power source such as an AC wall adaptor,
computer or car port. Charge rates may vary depending on the power
source’s maximum output.
2. To expose the USB port, twist the ring to align the • with the .
NOTE: Always close the USB cover when light is not charging to maintain
dust and moisture protection.
3. Insert the USB plug into the USB port.
4. The indicator light will display the charging status:
Red Pulsing: Charging, 0-49%
Yellow Pulsing: Charging, 50-99%
Green Solid: Charging 100%
Red/Green Flashing: Cold, Wet, Faulty or No Battery
Red Solid: Over temperature (too hot)
Iftheindicatorlightashesredandgreen,checkthatthebatteryisfully
seated into the bay. Remove the battery and reinsert.
Iftheashlightstartstodimandtheindicatorlightilluminatessolidred,
the tool may be too hot.
The solid red indicator light will stay on until the tool has cooled. Once
the tool is within the acceptable range, normal charging and operation will
takeplace.
If problems persist, contact a MILWAUKEE service facility.
Operation
To reduce the risk of injury, do not stare at the operating
light source.
To avoid damage/discoloration to surfaces due to high temperatures,
do not set the light lens-down during use.
Press the power buttontoturnthelightonando.Pressandholdthe
power button to cycle through the modes: High, Medium, and Low. Release
the power button when you have reached desired mode. NOTE: The light
will default to the selected brightness setting the next time it is turned on.
The indicator light will display the battery life:
Red Flashing: 0-3% remaining Red Solid: 4-10% remaining
Yellow Solid: 11-49% remaining Green Solid: 50-100% remaining
To reduce the risk of injury, always unplug the charger
and remove the battery from the charger before perform-
ing any maintenance. The charger and battery have no internal service-
able parts. Never disassemble the battery or charger.
Maintenance and Storage
Store your charger in a cool, dry place.
As a general practice, it is best to unplug battery chargers and remove bat-
teries when not in use. No battery damage will occur, however, if the charger
and battery are left plugged in.
To reduce the risk of injury and damage, never immerse
your battery or charger in liquid or allow a liquid to ow
inside them.
Cleaning
Clean out dust and debris from charger vents and electrical contacts by blowing
with compressed air. Use only mild soap and a damp cloth to clean the battery
andcharger,keepingawayfromallelectricalcontacts.Certaincleaningagents
and solvents are harmful to plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated clean-
ing solvents, ammonia and household detergents containing ammonia. Never
useammableorcombustiblesolventsaroundbatteries,charger,ortools.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical Support with technical,
service/repair, or warranty questions.
Email:metproductsupport@milwaukeetool.com
BecomeaHeavyDutyClubMemberatwww.milwaukeetool.comtoreceive
importantnoticationsregardingyourtoolpurchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.877.948.2360
Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.ca
LIMITED WARRANTY - USA & CANADA
Every MILWAUKEE REDLITHIUM™ USB battery and charger* is warranted to the original purchaser from an authorized MIL-
WAUKEEdistributoronlytobefreefromdefectsinmaterialandworkmanship.Subjecttocertainexceptions,MILWAUKEEwill
repair or replace repair a REDLITHIUM™ USB battery or charger which, after examination, is determined by MILWAUKEE to be
defectiveinmaterialorworkmanshipforaperiodoftwo(2)yearsafterthedateofpurchaseunlessotherwisenoted.Returnofthe
REDLITHIUM™ USB battery or charger to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service
Station,freightprepaidandinsured,isrequired.Forthepropershippingprocedureofbatterypacks,contact1.800.SAWDUST
(1.800.729.3878),orgotowww.milwaukeetool.com.Acopyoftheproofofpurchaseshouldbeincludedwiththereturnproduct.
This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other
thanMILWAUKEEauthorizedpersonnel,misuse,alterations,abuse,normalwearandtear,lackofmaintenance,oraccidents.
Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part including,
but not limited to charging cables, and wall plugs.
*This warranty does not cover any cordless product sold with the REDLITHIUM™ USB battery and/or charger. There are
separate and distinct warranties available for these products.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF
THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION,
YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES
OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLU-
SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES
ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
PleaseconsulttheFindaServiceCenterSearchintheParts&ServicesectionofMILWAUKEE’swebsitewww.milwaukeetool.
comorcall1.800.SAWDUST(1.800.729.3878)tolocateyournearestMILWAUKEEfactoryServiceCenterlocation.
LIMITED WARRANTY - USA & CANADA
2010R MILWAUKEE
®
Rechargeable 250L Penlight w/ Laser, 2011R MILWAUKEE
®
Rechargeable 500L Everyday Carry Flashlight
w/ Magnet, and 2012R MILWAUKEE
®
RechargeableMagneticHeadlampandTaskLight.
The Rechargeable Personal Lighting Products referenced above are warranted to the original purchaser from an authorized
MILWAUKEEdistributoronlytobefreefromdefectsinmaterialandworkmanship.Subjecttocertainexceptions,MILWAUKEE
will repair or replace any part on the above Rechargeable Personal Lighting Products which, after examination, is determined
byMILWAUKEEtobedefectiveinmaterialorworkmanshipforaperiodoftwo(2)yearsafterthedateofpurchase.
All other MILWAUKEE Personal Lighting Products* (see exceptions below) are warranted to the original purchaser from an
authorizedMILWAUKEEdistributoronlytobefreefromdefectsinmaterialandworkmanship.Subjecttocertainexceptions,
MILWAUKEE will repair or replace any part on a personal lighting product which, after examination, is determined by MILWAUKEE
tobedefectiveinmaterialorworkmanshipforthelifetimeofsuchpersonallightingproducts.
Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part including,
butnotlimitedtoclips,straps,chargingcables,wallplugs,andrubbergaskets.ThiswarrantydoescovertheLEDinthepersonal
lightingproducts,subjecttothelimitationsherein.
*Thiswarrantydoes notcoverCordless BatteryPacksorChargers.Thereareseparateanddistinctwarrantiesavailable
for these products.
Return of all personal lighting products to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service
Station, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. The
above warranties do not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other
thanMILWAUKEEauthorizedpersonnel,misuse,alterations,abuse,normalwearandtear,lackofmaintenance,accidents,
orcausedbyalkalinebatteries.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF
THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION,
YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES
OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLU-
SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES
ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
PleaseconsulttheFindaServiceCenterSearchintheParts&ServicesectionofMILWAUKEE’swebsitewww.milwaukeetool.com
orcall1.800.SAWDUST(1.800.729.3878)tolocateyournearestMILWAUKEEfactoryServiceCenterlocation.
INSTRUCTIONS DE SÉCURITÉ
IMPORTANTES
- CONSERVER CES INSTRUCTIONS -
LIRE ET COMPRENDRE TOUTES LES
INSTRUCTIONS. Le non-respect des instruc-
tions ci-après peut entraîner des chocs électriques, des incendies et/ou
des blessures graves.
1. INSTRUCTIONS DE SÉCURITÉ IMPORTANTES - Ce manuel contient des
instructions importantes concernant la sécurité et le fonctionnement de la
lampe rechargeable par USB et la batterie USB REDLITHIUM™.
REDLITHIUM™ USB 1,100L TWIST FOCUS FLASHLIGHT
LAMPE DE POCHE FOCALISANTE TOURNANTE DE 1 100 L REDLITHIUM™ RECHARGEABLE PAR USB
LINTERNA CON ENFOQUE POR GIRO DE 1 100 L REDLITHIUM™ RECARGABLE POR USB
IMPORTANT SAFETY
INSTRUCTIONS
- SAVE THESE INSTRUCTIONS -
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in
electricshock,reand/orseriouspersonalinjury.
1. SAVE THESE INSTRUCTIONS - This manual contains important safety
and operating instructions for the REDLITHIUM™ USB battery and USB
rechargeable light.
2.
Use and charge only REDLITHIUM™ USB batteries in this
USB rechargeable light. Do not use counterfeit, aftermarket,
or "knocko" batteries or chargers. Do not wire a battery pack to a power
supply plug or car cigarette lighter.
3. Before using the battery and light, read the operator's manual and all labels
on the battery and light.
4. Use only with Listed/Certied ITE power supply.
5. Avoid dangerous environments. Do not charge battery in rain, snow, damp
or wet locations. Do not use battery or charger in the presence of explosive
atmospheres(gaseousfumes,dustorammable materials) because sparks
maybegeneratedwheninsertingorremovingbattery,possiblycausingre.
6. Charge in a well ventilated area.Donotblockchargervents.Keepthemclear
toallowproperventilation.Donotallowsmokingoropenamesnearacharging
battery. Vented gases may explode.
7. Maintain charger cord. When unplugging charger, pull plug rather than cord.
Never carry charger by its cord. Keep cord from heat, oil and sharp edges.
Makesurecordwillnotbesteppedon,trippedoverorsubjectedtodamageor
stress. Do not use charger with damaged cord or plug. Have a damaged charger
replaced immediately.
8. Use only recommended attachments.
9. Always unplug charger before cleaning or maintenance.
10. Do not burn or incinerate batteries. Battery may explode. Toxic fumes and
materials are created when battery are burned.
11. Do not crush, drop, or damage battery pack. Always securely contain battery
packsduringtransport.Donotuseabatterypackthathasreceivedasharp
blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail,
hit with a hammer, stepped on, in a vehicle accident).
12. Do not disassemble.Ifitisdamaged,takeittoaMILWAUKEEservicefacility.
13. Battery chemicals cause serious burns.Neverallowcontactwithskin,eyes,
ormouth.Ifadamagedbatteryleaksbatterychemicals,userubberorneoprene
glovestodisposeofit.Ifskinisexposedtobatteryuids,washwithsoapand
water and rinse with vinegar. If eyes are exposed to battery chemicals, imme-
diatelyushwithwaterfor20minutesandseekmedicalattention.Removeand
dispose of contaminated clothing.
14. Do not short circuit. Ashort-circuitedbatterypackmaycausere,personal
injury,andproductdamage.Abatterypackwillshortcircuitifametalobject
makesaconnectionbetweenthepositiveandnegativecontactsonthebattery
pack.Donotplaceabatterypacknearanythingthatmaycauseashortcircuit,
suchascoins,keysornailsinyourpocket.
15. Do not allow uids to ow into battery pack. Corrosiveorconductiveuids,
such as seawater, certain industrial chemicals, and bleach or bleach contain-
ing products, etc., can cause a short circuit.
16. Store in a cool, dry place. Do not store battery where temperatures may
exceed 120°F (50°C) such as in direct sunlight, a vehicle, or metal building
during the summer.
17. To reduce the risk of injury, close supervision is necessary when an ap-
pliance is used near children.
18. Store idle light out of reach of children. Warm lights can become hazardous
in the hands of children.
19. Know your light. Read this manual carefully to learn your light's applications
and limitations as well as potential hazards associated with this type of light.
20. Maintain labels and nameplates. These carry important information. If unread-
able or missing, contact a MILWAUKEE service facility for a free replacement.
SYMBOLOGY
V
Volts
Amps
Read Operator's Manual
Do not stare at the
operating light source.
Light becomes warm during
use. Turn OFF before storing
or setting down to avoid heat
buildup.
Universal Serial Bus (USB)
Direct Current
BFP
BackfeedProtected
Properly Recycle
Batteries
EuropeanConformityMark
Do not dispose together
with household waste.
SPECIFICATIONS
Cat. No. ........................................................................................................2161-20
USB Input Volts .................................................................................................5 DC
USB Input Amps ........................................................................................0.1 - 2.1 A
Output Volts .......................................................................................................4 DC
Output Amps ...................................................................................................... 2.1 A
REDLITHIUM
™
USB Batteries
Volts ..................................................................................................................4 DC
Wall Plug Input Volts ......................................................................... 120 AC
Operating Temperature
Battery and Charger .............................................
40°F to 104°F (4°C to 40°C)
Battery and Tool ..........................................-4°F to 140°F (-20°C to 60°C)
Cord Cat. No. ...............................................................................42-44-1210
BATTERY
To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool,
battery pack or charger in uid or allow a uid to ow inside them. Corro-
sive or conductive uids, such as seawater, certain industrial chemicals,
and bleach or bleach containing products, etc., can cause a short circuit.
Maintenance and Storage
Do not expose your battery or cordless tools to water or rain, or allow them
to get wet. This could damage the tool and battery. Do not use oil or solvents
to clean or lubricate your battery. The plastic casing will become brittle and
crack,causingariskofinjury.
Store batteries at room temperature away from moisture. Do not store in
damp locations where corrosion of terminals may occur. As with other battery
types,permanentcapacitylosscanresultifthepackisstoredforlongperiods
of time at high temperatures (over 120° F). MILWAUKEE Li-Ion batteries
maintain their charge during storage longer than other battery types. After
about a year of storage, charge the battery as normal.
To reduce the risk of injury or explosion, never burn or
incinerate a battery pack even if it is damaged, dead or
completely discharged. When burned, toxic fumes and materials are
created.
Disposing of MILWAUKEE Li-Ion Battery
MILWAUKEE Li-Ion batteries are more environmentally friendly than some
other types of power tool batteries. Always dispose of your battery according
to federal, state and local regulations. Contact a recycling agency in your
area for recycling locations.
Even discharged batteries contain some energy. Before disposing, use
electrical tape to cover the terminals to prevent the battery from shorting,
whichcouldcauseareorexplosion.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see "Symbology") on your batteries
indicate that MILWAUKEE has arranged for the recycling of that battery with
the Rechargeable Battery Recycling Corporation (RBRC). At the end of your
battery'susefullife,returnthebatterytoaMILWAUKEEBranchOce/Service
Center or the participating retailer nearest you. For more information, visit
the RBRC web site at www.rbrc.org.
2.
Utiliser et charger uniquement les batteries USB
REDLITHIUM™ avec cette lampe rechargeable USB. Ne
pas utiliser des batteries ou des chargeurs contrefaits, falsifiés ou
« truqués ». Ne pas relier un bloc-piles à une prise secteur ou à un al-
lume-cigare.
3. Avant d’utiliser la pile et la lampe de poche, lisez ce manuel de l’operateur ain-
si que toutes les étiquettes qui se trouveront sur la lampe de poche et la pile.
4. Utiliser uniquement avec une source d’alimentation ITE listée/certiée.
5. Évitez des milieux dangereux. Ne chargez pas la pile dans des milieux ayant
de la pluie, neige, humidité ni d’environnements mouillés. N’utilisez pas la pile
ni le chargeur dans des atmosphères explosives (ayant des vapeurs gazeux,
poudreoumatérielinammable)parcequedesétincellespourrontêtrecréées
lorsque la pile est insérée ou retirée, pouvant bien provoquer des incendies.
6. Chargez-la dans un espace bien aéré. Ne bloquez pas les bouches du char-
geur. Préservez-las propres pour assurer une bonne aération. Ne laissez pas
defumesniamesdécontrôléesprèsd’unepileduchargeur.Lesgazaérés
pourront exploser.
7. Entretenir le cordon du chargeur. Lors du débranchement du chargeur, tirez
surlacheplutôtquesurlecordon.Neportezjamaislechargeurparsoncordon.
Gardez le cordon de la chaleur, de l’huile et des bords tranchants. Assurez-vous
que le cordon ne sera pas mis sur un pied, trébuché ou soumis à des dommages
ouàdustress.N’utilisezpasdechar-geravecuncordonouunecheendom-
magé. Faites remplacer immédiatement un chargeur endommagé.
8. Utiliser exclusivement les accessoires recommandés.
9. Débranchez toujours le chargeur avant de le nettoyer ou l’entretenir.
10. Ne pas brûler ou incinérer les piles. Les batteries peuvent exploser. Des
vapeurs et des matériaux toxiques sont créés lorsque les batteries sont brûlées.
11. Ne pas écraser, laisser tomber ou endommager les blocs-piles. Toujours
mettre les blocs-piles dans un conteneur sûr durant le transport. Ne pas utiliser
une batterie ou un chargeur qui ont subi un choc violent, ont été écrasés ou
endommagés de quelque façon que ce soit (par exemple, s’ils ont été percés
par un clou, frappés avec un marteau ou piétinés).
12. Ne pas désarmer le bloc-piles. Sijamaisilestendommagé,leconeràun
centre de service MILWAUKEE.
13. Les produits chimiques entraînent des brûlures graves. Ne permettez pas
qu’ils entrent en contact avec la peau, les yeux ni la bouche. Si de la pile en-
dommagée des produits chimiques se coulent, utilisez des gants en caoutchouc
ounéoprènepoursedébarrasserd’elle.Silapeauestexposéeàdesuides
de la pile, lavez-la avec du savon et de l’eau et rincez-la avec du vinaigre. Si
les yeux sont exposés aux produits chimiques de la pile, lavez-les avec pleine
del’eaupendant20minutesetconsultezunmédecin.Retirezlesvêtements
contaminés et se débarrassez d’eux.
14. Ne pas court-circuiter. Un bloc-piles court-circuité pourra mener un incendie,
des blessures physiques et endommager le produit. Un bloc-piles court-circuitera
siunobjetmétalliqueétablituneconnexionentrelescontactspositifetnégatifdu
bloc-piles. Mettre le bloc-piles à l’écart de tout ce qui pourra causer un court-cir-
cuit, tel que des pièces de monnaie, des clés ou des clous dans votre poche.
15. Ne pas laisser les uides entrer dans le bloc-piles.Lesuidescorrosifset
conducteurs, tels que l’eau de mer, quelques produits chimiques industriels
etsolutionsd’eaudejaveloud’autresproduitsayantdel’hypochlorite,etc.,
Pourront provoquer des courts-circuits.
16. Conserver dans un endroit frais et sec. N’entreposez pas de batterie là où
les températures peuvent dépasser 50°C (120°F), comme en plein soleil, un
véhicule ou un bâtiment métallique pendant l’été.
17. An de réduire le risque de blessures, supervision étroite est requise
quand un appareil est utilisé près d’enfants.
18. Tenez l’indicateur de repos hors de la portée des enfants. Des lumières
chaudespeuventêtredangereusesdanslaportéedesenfants.
19. Connaissez votre lampe. Lisez attentivement ce manuel de l’opérateur pour
savoir à propos des applications et limitations de la lampe ainsi que les dangers
possibles liés à ce type de lampe.
20. Préservez les étiquettes et plaques nominatives. Elles montrent d’information
importante. Si elle est illisible ou manquante, contactez un centre de service
MILWAUKEEanderecevoirunoutilsubstitutifgratuit.
PICTOGRAPHIE
V
Volts
Ampères
Lisez le manual de
l'operateur
Ne pas regarder la
source de lumière de
fonctionnemente.
La lampe devient chaude durant
l’utilisation. Éteindrelalampe avant
de l’entreposer ou de la déposer,
ceci pour éviter que la chaleur ne
s’accumule.
Bus universel série
(USB)
Courant direct
BFP
Rétro-alimentation
protégée
Recyclage correct
des batteries
Marque de conformité
aux normes
européennes
Nepasjeteravec
l’ordure domestique.
SPECIFICATIONS
No de Cat. .................................................................................................... 2161-20
Voltage d’entrée par USB ....................................................................5 CD
Ampérage d’entrée par USB .......................................................0,1 - 2,1 A
Voltage de sorti .................................................................................... 4 CD
Ampérage de sorti ................................................................................2,1 A
REDLITHIUM
™
Bloc-piles USB
Tension .................................................................................................4 CD
Tension d’entrée de prise murale ....................................................120 CA
Température opérative
Pile et chargeur ............................................
4°C to 40°C (40°F to 104°F)
Pile et outil ...................................................
-20°C to 60°C (
-4
°F to 140°F)
No de Cat. de cordon .................................................................42-44-1210
BLOC-PILES
Pour réduire le risque d’incendie, de blessures
corporelles et de dommages causés par un
court-circuit, ne jamais immerger l’outil, le bloc-piles ou le chargeur
dans un liquide ou laisser couler un uide à l’intérieur de celui-ci. Les
uides corrosifs ou conducteurs, tels que l’eau de mer, certains produits
chimiques industriels, les produits de blanchiment ou de blanchiment,
etc., peuvent provoquer un court-circuit.
Entretien et entreposage
Nepasexposervotrebloc-pilesnivosoutilssanslàl’eauoulapluie,oules
laisser prendre l'humidité. Cela pourrait endommager l’outil et le bloc-piles.
Nepasutiliserd'huileousolvantspournettoyeroulubriervotrebloc-piles.
Le boîtier du bloc-piles risque de devenir cassant ou de se fendiller, causant
un risque de blessure.
Entreposer les blocs-piles à température ambiante à l'abri de l’humidité. Ne
pas les entreposer dans un endroit humide où la corrosion des bornes peut
survenir. Comme pour d'autres types de batteries, une perte permanente de
capacité peut survenir si le bloc-piles est entreposé pendant longtemps à
hautetempérature(48°C/120°F).LespilesLi-ionMILWAUKEEmaintiennent
leur charge pendant plus longtemps que les autres types de piles. Après un
an d'entreposage, rechargez le bloc-piles comme d’habitude.
Pour réduire le risque d'explosion, ne jamais
brûler un bloc-piles, même s'il est endommagé
ou complètement déchargé. Lorsqu’il est brûlé, des matières et vapeurs
toxiques sont produites.
Mise au rebut du bloc-piles Li-ion MILWAUKEE
Les blocs-piles Li-ion MILWAUKEE sont plus écologiques que d’autres types
de piles pour outils portables. Mettre au rebut votre bloc-piles conformément
aux réglementations locales, nationales et fédérales. Contacter une agence
de recyclage dans votre région pour les lieux de recyclage.
Mêmedéchargés,lesblocs-pilescontiennentunpeud’énergie.Avantlamise
aurebut,utiliserdurubanisolantpourrecouvrirlescontactspourempêcher
la mise en court-circuit, laquelle pourrait causer un incendie ou une explosion.
Sceaux de recyclage des blocs-piles RBRC
Les sceaux de recyclage des batteries RBRC™ (voir « Symbologie ») sur vos
blocs-piles indiquent que MILWAUKEE a pris des dispositions pour le recyclage
de ce bloc-piles avec la Société de recyclage des piles rechargeables (RBRC).
Àlandeladuréedevieutiledubloc-piles,leretourneràunesuccursaleouun
centre de service MILWAUKEE ou au détaillant participant le plus proche de chez
vous. Pour plus d'informations, consulter le site Web de RBRC www.rbrc.org.