Minetan Bronze Babe Personal

To Next Page

CUSTOMER CARE

FAILURE TO OPERATE

IMPORTANT SAFETY PRECAUTIONS

TAN.HANDY OPERATION MANUAL

REMOVING THE SPRAY TAN GUN

1. To begin, attach the

Tan.Handy spray tan gun to

the Tan.Handy mini turbine

by inserting the bottom of

the handle of the spray tan

gun into the connector of

the mini-turbine.

2. Attach the Tan.Handy

spray tan gun with the

‘quick-connect’ style tting.

This will lock the spray tan

gun rmly into place.

To remove the Tan.Handy mini-

turbine for cleaning and relling

solution cup, detach the spray

gun with the ‘quick-connect’

tting and remove it from the

mini-turbine.

3. Once the spray tan

gun is attached to the

mini-turbine, insert the

power cord into the

device and in the wall

plug and turn power

on at the wall switch.

Before using this Tan.Easy Product, read all instructions and cautionary markings

in this manual and on the device. When using an electrical appliance, basic

precautions should always be followed:

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1. Do not leave product when plugged in. Unplug from outlet when not in use and

before servicing.

2. Indoor Use ONLY. Do not use outdoors or on wet surfaces. Store Indoor ONLY.

3. Do not allow to be used as a toy. Close attention is necessary when used by or

near children.

4. This product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

5. Use this device only for its intended function and do not use attachments not

recommended by the authorized Tan.Easy Pro Tools manufacturer.

6. Do not use the device if the cord is damaged. In the event of damage

discontinue use immediately. If the supply cord is damaged, it must be replaced

by the authorized Tan.Easy Pro Tools manufacturer.

7. If device is not working as it should, has been dropped, damaged, le outdoors,

or dropped into water, do not use, contact Tan.Easy Pro Tools Customer Care via

the website or regional telephone number.

8. Do not pull or carry by cable, use cable as a handle, close a door on cable,

or pull cable around sharp edges or corners. Keep cable away from heated

surfaces.

9. Do not unplug by pulling on cable. To unplug, grasp the plug, not the cable.

10. Do not handle plug with wet hands.

11. Turn o all controls before unplugging.

12. Do not spray ammable or combustible liquids, such as gasoline, or use in areas

where they may be present.

13. Do not use without the lter in place.

14. Do not use an extension cord unless the cord complies with local region

electrical safety standards.

15. Periodically inspect the power cord for signs of damage

16. Do not use a uid having a ash point higher than 60ºC. When a combustible

liquid is sprayed there can be danger of re or explosion, especially in a closed

area. Read instruction manual before operating.

17. Fuse is only able to be replaced by manufacturer.

IMPORTANT: This device is designed for 220-240V or 120V respectively depending on

region. Always check that the voltage of your electricity supply matches the voltage

of your Tan.Easy Pro Tools device.

1. Do not use this product with a voltage inverter or any device designed to convert

the electrical supply to 220-240V or 120V from a dierent source.

2. Always ensure that your appliance

is connected to a properly earthed

power supply. Your Tan.Easy Pro Tools

Device is a class II electrical appliance.

Thank you for choosing to purchase this Tan.Easy Pro Tools product. Your Tan.Easy Pro

Tools device will be covered for parts only for 12 months from the date of purchase, as

detailed in the terms of the Tan.Easy Pro Tools guarantee on taneasyprotools.com.

If you have a query about your Tan.Easy Pro Tools product, contact Tan.Easy Pro Tools

by going to the website taneasyprotools.com.

Most queries can be solved by our frequently asked questions online. Alternatively you

can contact your local Tan.Easy representative in your region.

Please state your serial number for any warranty claims you have. Your serial number

can be found on the rating plate, which is on the base of your machine or below:

In the unlikely event that your Tan.Handy device does not operate correctly,

check that the Tan.Handy product and main power supply are switched on, and

that power is available.

For UK plugs, please ensure that the tted fuse is intact and functioning; if it is not,

replace it with an identically rated British Standard Fuse.

If in doubt or for further advice, please visit the Support and Trouble shooting

page at taneasyprotools.com or contact an approved Tan.Easy stockist or

contact Tan.Easy Customer services for further advice.

REVISION DATE 9.07.15 #1

All rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without prior written consent of Tan.Easy Pro

Tools.NOTICE

The information contained in this document is subject to change without notice

and should not be construed as a commitment by Tan.Easy Pro Tools. Tan.Easy Pro

Tools assumes no responsibility for any errors that may appear in this document nor

does it make expressed or implied warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

tness for a particular purpose. Tan.Easy Pro Tools shall not be liable for incidental

or consequential damages in connection with or arising out of the use of this

document and the program material.

The MineTan Tan.Handy has been designed by the team

at Tan.Easy Pro Tools, the experts in professional tanning

equipment, to give you the perfect spray tan at home.

PA R T N ER IN G W I T H TA N . E A S Y P R O TO O L S

ASSEMBLY

BRONZE BABE

PERSONAL

SPRAY TAN KIT

TROUBLESHOOTING Refer to taneasyprotools.com

This is for example purposes only. Note your serial number for future reference

SERIAL NUMBER

SERIAL

NUMBER

SERIAL

NUMBER

Do not pull

on cables.

Do not submerge

in water or get wet.

Do not use near

open ames

FOR TROUBLE SHOOTING & SUPPORT GO TO

TANEASYPROTOOLS.COM

TAN.EASY PRO TOOLS

80 Market St, South Melbourne, 3205 TANEASYPROTOOLS.COM

FOR MORE INFORMATION SEE OPERATION MANUAL MADE IN CHINA

TAN.EASY PRO TOOLS

80 Market St, South Melbourne, 3205 TANEASYPROTOOLS.COM

FOR MORE INFORMATION SEE OPERATION MANUAL MADE IN CHINA

TAN.HANDY MOBILE SPRAY TAN GUN

ITEM NO# 1001001 M1002-18000

150W 120V~60HZ 1.2A

TAN.HANDY MOBILE SPRAY TAN GUN

ITEM NO# 1001001 M1002-18000

150W 240V~60HZ 1.2A

Need help?

Do you have a question about the Minetan Bronze Babe Personal and is the answer not in the manual?

Summary

Important Safety Precautions

General Safety Guidelines

Essential safety warnings for product usage, electrical safety, handling, and maintenance.

Customer Care and Warranty Information

Product Serial Number Location

Guidance on finding your product's serial number for warranty claims and support.

Assembly and Operation

Attaching the Spray Tan Gun

Step-by-step instructions for connecting the spray tan gun to the mini-turbine.

Removing the Spray Tan Gun

Instructions on how to detach the spray gun for cleaning and refilling purposes.

Using Your Tan. Handy

Pre-Tanning Skin Preparation

Steps for preparing your skin before tanning, including exfoliation and dryness.

Setting the Spray Pattern

Adjusting the nozzle to achieve preferred spray patterns for tanning.

Spray Tan Technique

Guidance on holding the device and applying spray for even tanning results.

Cleaning and Maintenance

Cleaning the Tan. Handy Filter

Instructions for cleaning the unit's filter with cold water, avoiding detergents.

Cleaning the Tan. Handy Spray Tan Gun

Procedure for cleaning the spray gun and cup after each use with warm water.

Storage and Manufacturers Guarantee

Proper Storage Guidelines

Recommendations for cooling down and storing the Tan. Handy after use.

Manufacturers Guarantee Terms

Details on the 12-month guarantee, claims process, and exclusions.

This document describes the Tan.Handy Personal Spray Tan Kit, a device designed for at-home spray tanning. It is a class II electrical appliance, meaning it requires a properly earthed power supply.

Function Description

The Tan.Handy Personal Spray Tan Kit is designed to provide a perfect spray tan at home. It consists of a mini-turbine and a spray tan gun that work together to apply tanning solution evenly to the skin. The device is intended for personal use and aims to replicate the results of professional tanning equipment.

Important Technical Specifications

The device operates on either 220-240V or 120V, depending on the region, with a frequency of 60Hz. It has a power rating of 150W and draws 1.2A. The serial number for the device can be found on the rating plate, typically on the base of the machine. The manufacturer is Tan.Easy Pro Tools, located at 80 Market St, South Melbourne, 3205.

Usage Features

Assembly:

Attach Spray Tan Gun to Mini-Turbine: Insert the bottom of the spray tan gun's handle into the connector of the mini-turbine.
Secure Connection: The spray tan gun features a 'quick-connect' style fitting that locks it firmly into place with the mini-turbine.
Power Connection: Once the gun is attached, insert the power cord into the device and then into a wall plug. Turn on the power at the wall switch.

Removing the Spray Tan Gun: To remove the spray tan gun for cleaning or refilling the solution cup, detach it using the 'quick-connect' fitting and then remove it from the mini-turbine.

Pre-Tanning Preparation:

Exfoliation: Prior to tanning, exfoliate the skin using an exfoliating mitt to ensure a smoother application and even fading.
Clean and Dry Skin: Ensure skin is completely clean and dry. Avoid applying moisturisers, oils, deodorants, or perfumes.
Hair and Jewelry: Put hair up with a plastic cap and remove all jewelry.
Waxing/Shaving: Perform waxing or shaving at least 24 hours before tanning.
Patch Test (for sensitive skin): If skin is very sensitive, conduct a patch test a minimum of 12 hours prior to full application.

Setting Spray Pattern: The device allows adjustment of the spray-pattern nozzle to suit preferred tanning styles:

Spraying Side to Side (Across the Body): Set the nozzle fan to 'Horizontal'. This pattern is ideal for spraying left-to-right or right-to-left across the body.
Spraying Up & Down (Up & Down the Body): Set the nozzle fan to 'Vertical'. This pattern is perfect for spraying top-to-bottom or bottom-to-top.

Operation:

Power On/Airflow: Turn the device on by pressing the on switch. The Tan.Handy features an intelligent Air-Smart Switch that controls airflow for a perfect spray, aiming for flawless results.

Spray Tan Technique:

Distance: Hold the Tan.Handy approximately 10-15cm (4-6") away from the skin.
Application Motion: Start at the feet and work upwards using sweeping, steady motions. Keep the Tan.Handy moving continuously to avoid dark spots.
Correcting Dark Spots: If a dark spot occurs, smooth it out immediately with an Application Mitt and continue spraying.
Coverage: Work your way up the entire body, ensuring complete and even coverage.
Avoid Specific Areas: Avoid spraying directly on heels, knees, and elbows to prevent deeper tanning.
Drying: Allow the tan to dry before wearing clothing. Follow product instructions for best results. Avoid swimming or exercising for the next 24 hours.

Storage:

Cool Down: Always allow the Tan.Handy to cool down before storing.
Cord Management: Once cooled, fold the power cord as it was originally packaged. Do not wrap the cord around the device, as this can strain the cord and cause premature failure.
Solution Storage: Any spray tan solution will last longer if stored in the refrigerator after opening.

Maintenance Features

Cleaning Your Tan.Handy Filter: The filter is located at the front of the mini-turbine.

Disconnect Power: Always disconnect the device from the supply circuit before cleaning or removing filters.
Remove Filter Cover: Remove the filter cover from the mini-turbine.
Wash Filter: Wash the filter under cold water. Do not use detergents.
Dry Completely: Allow the filter to dry completely before re-inserting.
Frequency: Wash the mini compressor filter with water at least every 6 months.

Cleaning Your Tan.Handy Spray Tan Gun: Clean the spray tan gun after each use. Do not use alcohol, acetone, petrol, or any abrasive-cleaning agents.

Remove Spray Tan Gun: Remove the spray tan gun from the Tan.Handy Mini Turbine.
Empty Solution Cup: Unscrew the cup from the spray gun and empty any unused solution.
Rinse Solution Cup: Rinse the empty solution cup with warm water until clean, then fill it about ¼ full of warm water.
Reassemble: Insert the cup and screw it tightly back into the spray tan gun, then reconnect to the mini-turbine.
Clean Nozzle: Turn on the Tan.Handy and direct the spray tan gun into a sink. Spray the clean water through until the cup is empty. This cleans through the needle and out to the spray-pattern nozzle.
Disconnect and Unscrew: Disconnect the spray tan gun from the mini-turbine and unscrew the cup.
Wipe Dry: Wipe all areas dry with a cloth, including the cup and Tan.Handy, ready for next use.
Important Note: Do not submerge the spray gun under water. If there is excess spray solution, wipe down with cleaning wipes. Alternatively, use a smooth cloth (avoiding anything abrasive) with a general glass cleaner to maintain the gloss finish.

Safety Precautions

The manual outlines several important safety precautions:

Unplug When Not in Use: Always unplug the product from the outlet when not in use and before servicing.
Indoor Use Only: The device is for indoor use only; do not use outdoors or on wet surfaces.
Children: Close attention is necessary when used by or near children. The product is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised.
Intended Use: Use the device only for its intended function and with attachments recommended by the manufacturer.
Damaged Cord: Do not use the device if the cord is damaged. Discontinue use immediately and have it replaced by the manufacturer.
Malfunction/Damage: If the device is not working correctly, has been dropped, damaged, or dropped into water, do not use; contact customer care.
Cord Handling: Do not pull or carry by the cable, use it as a handle, close a door on it, or pull it around sharp edges. Keep the cable away from heated surfaces.
Unplugging: Grasp the plug, not the cable, to unplug.
Wet Hands: Do not handle the plug with wet hands.
Turn Off Controls: Turn off all controls before unplugging.
Flammable Liquids: Do not spray flammable or combustible liquids (e.g., gasoline) or use in areas where they may be present.
Filter: Do not use without the filter in place.
Extension Cord: Do not use an extension cord unless it complies with local electrical safety standards.
Power Cord Inspection: Periodically inspect the power cord for signs of damage.
Flash Point: Do not use a fluid with a flash point higher than 60°C.
Fuse Replacement: The fuse can only be replaced by the manufacturer.
Voltage Compatibility: Always check that the voltage of your electricity supply matches the device's voltage (220-240V or 120V).
Voltage Converters: Do not use this product with a voltage inverter or any device designed to convert electrical supply from a different source.
Earthed Supply: Ensure the appliance is connected to a properly earthed power supply.
Submersion: Do not submerge the device in water or get it wet.
Open Flames: Do not use near open flames.

Troubleshooting

If the device does not operate correctly, check that the product and main power supply are switched on and that power is available. For UK plugs, ensure the fitted fuse is intact and functioning; if not, replace it with an identically rated British Standard Fuse. Further advice and support can be found at taneasyprotools.com.

Manufacturer's Guarantee

All Tan.Easy Pro Tools devices are individually tested. In case of defects due to faulty workmanship or materials, Tan.Easy Pro Tools will repair or replace the product at no charge with an identical or equivalent product within one year from the original purchase date. A replacement product assumes the remaining warranty of the original product, or provides longer coverage if applicable. The guarantee applies only to genuine Tan.Easy Pro Tools products purchased through approved stockists and does not cover products repaired by unauthorized personnel. The guarantee may be invalidated if serial numbers or identification are erased, damaged, or modified. This does not affect statutory rights.

The guarantee does not cover:

Damage caused by misuse, improper treatment, or violent usage.
Damage caused by failure to comply with instructions for use.
Damage caused by connecting the appliance to the incorrect voltage.
Damage caused by connecting accessories supplied by other manufacturers.
Minor faults that do not significantly affect the device's value or effective use.

Australia Only: Goods come with guarantees under Australian Consumer Law. Consumers are entitled to a replacement or refund for a major failure and compensation for foreseeable loss or damage. They are also entitled to repair or replacement if goods fail to be of acceptable quality and the failure does not amount to a major failure.