Mitsubishi Electric FR-F840-00023 User Manual

Mitsubishi Electric FR-F840-00023

940 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

INDUSTRIAL AUTOMATION

MITSUBISHI ELECTRI

C

MITSUBISHI ELECTRI

C

FR-F800

Inverter

Instruction Manual

FR-F820-00046(0.75K) to 04750(110K)(-E)

FR-F840-00023(0.75K) to 06830(315K)(-E)

FR-F842-07700(355K) to 12120(560K)(-E)

Art. no.: 292550

01 06 2017

Version C

Version check

Table of Contents

Other manuals for Mitsubishi Electric FR-F840-00023

Installation Guidelines64 pages

Questions and Answers:

R
Richard PowersAug 7, 2025
How to fix incorrect motor speed on Mitsubishi Electric FR-F840-00023?
- D
  Dr. Kara BenjaminAug 7, 2025
  If the motor does not run at the correct speed, and there's a difference between the command speed and the actual speed, it could be due to noise affecting the speed command. Check that the speed command sent from the controller is correct and take EMC measures. Additionally, you can try setting Pr. 72 "PWM frequency selection" lower or adjusting the bias and gain (Pr. 125, Pr. 126, C2 to C7, C12 to C15) of the speed command again.
A
Ana DuffyAug 11, 2025
What to do if Mitsubishi Electric FR-F840-00023 machine movement is unstable?
- H
  Haley HunterAug 11, 2025
  If the machine movement is unstable, it could be due to a speed control gain that is not suitable for the machine. Adjust Pr. 820 and Pr. 821. Alternatively, the response might be slow because of the inverter's acceleration/deceleration time setting, so setting the optimum acceleration/deceleration time may help.
D
Dawn WilsonAug 16, 2025
Why is my Mitsubishi Electric FR-F840-00023 motor vibrating?
- J
  James DeckerAug 16, 2025
  If the motor or machine experiences hunting (vibration or acoustic noise), it may be due to a speed control gain that is too high. Try setting Pr. 820 “Speed control P gain 1” lower and Pr. 821 “Speed control integral time 1” higher. Another possible cause is a torque control gain that is too high; in this case, set Pr. 824 “Torque control P gain 1 (current loop proportional gain)” lower. Also, check the motor wiring to ensure it is correct.
C
Christina LoveAug 20, 2025
Why Mitsubishi Electric FR-F840-00023 Inverter speed does not accelerate?
- D
  Damon GarciaAug 20, 2025
  If the speed does not accelerate to the command speed, it could be due to torque shortage, causing the stall prevention operation level to activate. Try raising the stall prevention operation level. You could also increase the capacity or select PI control.
P
pacetammieAug 25, 2025
Why does Mitsubishi Electric FR-F840-00023 Inverter motor speed fluctuate?
- B
  bowencourtneyAug 26, 2025
  If the motor speed fluctuates, it could be because the speed command varies. Check that the speed command sent from the controller is correct and take EMC measures. You might also try setting Pr. 72 "PWM frequency selection" lower or setting Pr. 822 "Speed setting filter 1" higher. Another possibility is torque shortage, so raise the stall prevention operation level. Finally, the speed control gain might not be suitable for the machine, causing resonance, so adjust Pr. 820 "Speed control P gain 1" and Pr. 821 "Speed control integral time 1".
R
Raymond MccoyAug 28, 2025
What causes rotation ripple in Mitsubishi Electric FR-F840-00023?
- R
  Randy GonzalezAug 28, 2025
  If rotation ripple occurs during low-speed operation, it could be that a high carrier frequency is affecting the motor rotation. Try setting Pr. 72 "PWM frequency selection" lower. Another cause could be that the speed control gain is too low, in which case you should set Pr. 820 "Speed control P gain 1" higher.
D
Dr. Heidi NelsonSep 2, 2025
Why Mitsubishi Electric FR-F840-00023 Inverter motor does not run at the correct speed?
- M
  michael69Sep 2, 2025
  The motor might not run at the correct speed because the speed command from the controller differs from the actual speed, potentially due to noise. To resolve this: * Verify that the speed command sent from the controller is correct, taking electromagnetic compatibility (EMC) measures if needed. * Try setting Pr.72 PWM frequency selection lower. Another cause could be a difference between the command speed and the speed recognized by the inverter. In this case, readjust the bias and gain of the speed command using Pr.125, Pr.126, C2 to C7, and C12 to C15.

Mitsubishi Electric FR-F840-00023 Specifications

General

Model	FR-F840-00023
Series	FR-F840
Type	Inverter
Input Voltage	200-240V AC
Input Frequency	50/60 Hz
Protection Class	IP20
Cooling Method	Fan cooled
Model Number	FR-F840-00023
Control Method	V/F control
Frequency Range	400 Hz

Related product manuals

Preview: FR-F846-00023-L2

FR-F846-00023-L2

Preview: Mitsubishi Electric FR-F800

Mitsubishi Electric FR-F800

Preview: Mitsubishi Electric FR-F806-E

Mitsubishi Electric FR-F806-E

Preview: FR-F820-00077

Preview: FR-F820-00046

Preview: FR-F800 Series