*1 Each value inside ( ) indicates the number of occupied points.
3.4.2 Examples of input wiring [AC power type]
3.4.3 Examples of input wiring [DC power type]
Input response time Approx. 10ms
Input signal form
• Sink input:
No-voltage contact
input
NPN open
collector transistor
• Source input:
No-voltage contact
input
PNP open
collector transistor
Input circuit insulation
Photocoupler
insulation
Input operation display
LED on panel lights
when photocoupler is
driven.
Item Specification
L
N
S/S
0V
24V
X000
X001
X002
X003
L
N
S/S
0V
24V
X000
X001
X002
X003
1. Sink input type 2. Source input type
S/S
X000
S/S
X000
*
100 to 240V AC
Fuse
3-wire type
sensor
*
100 to 240V AC
Fuse
3-wire type
sensor
*Class D grounding
See section 3.3 for details.
[1] [1]
[2] [2]
[1]:Main unit, Input/output extension unit
(Common to both sink and source inputs)
[2]:Input/output extension block
(Common to both sink and source inputs)
X000
X001
X002
X003
3-wire type
sensor
*1
Fuse
*1 Class D grounding
See section 3.3 for details.
S/S
X000
X001
X002
X003
3-wire type
sensor
1.Sink input type 2.Source input type
S/S
X000
S/S
X000
[1] [1]
[2] [2]
[2]:Input/output extension block
(Common to both sink and source inputs)
[1]:Main unit, Input/output extension unit
(Common to both sink and source inputs)
S/S
*2
*2
*1
Fuse
*2
24V DC24V DC
Do not connect the [ ] terminals with others,
since they are not available.
3.4.4 Instructions for connecting input devices
As for the details of Instructions for connecting input devices, refer to
the following manual.
→ Refer to FX3G Series User's Manual - Hardware Edition.
1) In the case of no-voltage contact:
The input current of this PLC is 5 to 7mA/24V DC.
Use input devices applicable to this minute current.
If no-voltage contacts (switches) for large current are used,
contact failure may occur.
2) In the case of input device with built-in series diode:
The voltage drop of the series diode should be approx. 4V or
less.
When lead switches with a series LED are used, up to two
switches can be connected in series.
Also make sure that the input current is over the input-sensing
level while the switches are ON.
3) In the case of input device with built-in parallel resistance:
Use a device with a parallel resistance of 15kΩ or more.
When the resistance is less than 15kΩ, connect a bleeder
resistance.
4) In the case of 2-wire proximity switch:
Use a two-wire proximity switch whose leakage current is 1.5mA
or less when the switch is off.
When the current is 1.5mA or more, connect a bleeder
resistance.
3.4.5 Input specifications (100V AC input type)
3.4.6 Examples of 100V AC input wiring
3.5 Relay output specifications and example of
external wiring
As for the details of the relay output specifications and external
wiring, refer to the following manual.
→ Refer to FX3G Series User's Manual - Hardware Edition.
3.5.1 Relay output specifications
*1 Each value inside ( ) indicates the number of occupied points.
*2 Between 250V and 240V CE, UL, and cUL are not compliant.
Item Specification
Number
of input
points
FX2N-8EX-UA1/UL 8 points
FX2N-48ER-UA1/UL 24 points
Input connecting type
Refer to FX
3G Series
User's Manual - Hardware Edition
Input form
Input signal voltage 100V AC to 120V
Input impedance
Approx. 21kΩ/50Hz
Approx. 18kΩ/60Hz
Input signal current
4.7mA/100V AC 50Hz
6.2mA/110V AC 60Hz
ON input sensitivity
current
3.8mA/80V AC
OFF input sensitivity
current
1.7mA/30V AC
Input response time Approx. 25ms to 30ms
Input signal form Contact input
Input circuit insulation Photocoupler insulation
Input operation display
LED on panel lights when
photocoupler is driven.
Item Specification
Number
of output
points
FX2N-8ER
4 points(8 points)*
1
FX3G-14MR
6 points(8 points)*
1
FX2N-8EYR
8 points
FX3G-24MR
10 points(16 points)*
1
FX3G-40MR
,
FX
2N-32ER
,
FX2N-16EYR
16 points
FX3G-60MR
,
FX2N-48ER
24 points
Output connecting type
Refer to FX3G Series User's
Manual - Hardware Edition
Output form Relay
External power supply
30V DC or less
240V AC or less
*2
Max. load
Resistance load
2A/point
*3
Inductive load 80VA
Min. load 5V DC, 2mA (reference value)
Open circuit leakage current -
Response
time
OFF→ON
Approx. 10ms
ON→OFF
Circuit insulation Mechanical insulation
Display of output operation
LED lights when power is applied
to relay coil.
*
*Do not take input signals from loads generating surge.
L
N
COM
X000
X001
X002
COM
X000
X001
MC
*
Fuse
Input/
output
extension
unit
Input/
output
extension
block
To Next Page
Loading...
