To Next PageTo Next PageHow to fix a malfunctioning Mitsubishi Electric MSZ-LN25VGW remote?
If your Mitsubishi Electric Air Conditioner remote controller is malfunctioning, the batteries might be weak. Replacing the batteries should allow the remote controller to operate normally.
How to fix Mitsubishi Electric Air Conditioner remote controller malfunction?
Weak batteries can cause the remote controller for your Mitsubishi Electric Air Conditioner to malfunction. Replace the batteries to ensure normal operation.
What to do if the POWER lamp on my Mitsubishi Electric MSZ-LN25VGW flashes 4 times?
If the POWER lamp on your Mitsubishi Electric Air Conditioner flashes 4 times, it indicates a problem with the indoor unit control system. The suggested solution is to replace the indoor electronic control P.C. board.
What does it mean when the POWER lamp on my Mitsubishi Electric Air Conditioner flashes 7 times?
If the POWER lamp on your Mitsubishi Electric Air Conditioner flashes 7 times, it suggests an issue with the outdoor control system. The solution involves replacing the inverter P.C. board or the outdoor electronic control P.C. board.
What to do if POWER lamp blinks 4 times on Mitsubishi Electric Air Conditioner?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 4 times, it means there's a problem with the indoor unit's control system. The suggested solution is to replace the indoor electronic control P.C. board.
What does POWER lamp 7-time blink mean on Mitsubishi Electric Air Conditioner?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 7 times, it indicates a problem with the outdoor control system. The solution is to replace either the inverter P.C. board or the outdoor electronic control P.C. board.
What to do if POWER lamp blinks 2 times on Mitsubishi Electric MSZ-LN25VGW?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 2 times, it indicates a problem with the room temperature or indoor coil thermistor in the indoor unit. Check the room temperature thermistor and the indoor coil thermistor, referring to section 10-7, "Test point diagram and voltage."
Why POWER lamp blinks 5 times on Mitsubishi Electric Air Conditioner?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 5 times, it indicates an abnormality in the outdoor power system. Refer to "How to check inverter/compressor."
What does POWER lamp 6-time blink mean on Mitsubishi Electric Air Conditioner?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 6 times, it indicates a problem with the thermistor in the outdoor unit. Refer to "Check of outdoor thermistors."
What does POWER lamp 3-time blink mean on Mitsubishi Electric MSZ-LN25VGW Air Conditioner?
If the POWER lamp on your Mitsubishi Electric Air Conditioner blinks 3 times, it indicates a problem with the indoor fan motor. Refer to section 10-6, "Check of indoor fan motor."
General| Brand | Mitsubishi Electric |
|---|---|
| Model | MSZ-LN25VGW |
| Category | Air Conditioner |
| Language | English |
Displays meanings of symbols on indoor and outdoor units and manual.
Covers essential safety guidelines for operation and handling.
Guidelines for safe installation of the air conditioner.
Guidelines for safe use of the Wi-Fi interface.
Identifies and describes parts of the indoor unit.
Explains the buttons and display of the remote controller.
Identifies and describes parts of the outdoor unit.
Instructions for installing batteries in the remote controller.
Procedure to set the current time on the remote controller.
Configures the remote controller for the indoor unit's position.
Pairs a remote controller to a specific indoor unit.
Steps to enable and disable the i-see sensor control mode.
Details on AUTO, COOL, DRY, HEAT, and FAN operating modes.
Adjusting vertical and horizontal airflow directions.
Procedure for selecting different fan speeds.
Customizing airflow based on occupant location.
Enabling energy-saving or auto-off modes when room is unoccupied.
Recalls preset preferred settings with a single button press.
Performs energy-saving cooling with automatic airflow adjustment.
Reduces operation noise and dims indicator lights.
Activates the indoor unit's device to reduce airborne contaminants.
Maximizes cooling or heating performance for a short period.
Instructions for setting and removing ON/OFF timers.
Programming and verifying weekly operating schedules.
Enables or disables the operation lock feature.
Details on emergency cooling, heating, and stop modes.
Instructions for cleaning air filters, purifying device, and front panel.
Introduction to the Wi-Fi interface and connection setup.
Common issues and solutions for the indoor unit.
Troubleshooting steps for the remote controller.
Solutions for operational, noise, and timer-related problems.
Resolving issues related to the Wi-Fi interface connection.
Steps for preparing the unit for storage and for re-use.
Recommendations for optimal installation and electrical connections.
Technical details including model, capacity, and operating parameters.
Technical details for the Wi-Fi interface module.
Information for installer contact and system configuration details.
