Mitsubishi FDT125VNPWVH - Page 13

'22 • PAC-SM-412
-
12
-
(6) Hot keep
Hot keep control is performed at the start of the defrost operation.
(a) Contents of operation
(i)Whentheindoorheatexchangertemperature(detectedwithThi-R1orR2)dropstolessthan35°C,thespeedofindoor
fanfollowsfansettingatthetimeofthermostatOFF.
(ii)Duringthehotkeep,thelouveriskeptatthehorizontalposition.
(7) Auto swing control (FDT, FDE only)
Note Even if [Auto Swing] is selected, the louver position with anti draft function is fixed to position 1.
(a) RC-EXZ3A
(i)Louvercontrol
1)Tooperatetheswinglouverwhentheair-conditionerisoperating,pressthe“Direction”buttonontheTOPscreen
of remote control. The wind direction select screen will be displayed.
2)Toswingthelouver,touchthe“Autoswing”button.Theloverwillmoveupanddown.Toxtheswinglouverata
position,touchoneof[1]-[4]buttons.Theswingloverwillstopattheselectedposition.
3)Louveroperationatthepoweronwithaunithavingthelouver4-positioncontrolfunction
Thelouverswingsonetimeautomatically(withoutoperatingtheremotecontrol)atthepoweron.
Thisallowsthemicrocomputerrecognizingandinputtingthelouvermotor(LM)position.
(ii)Automaticlouverlevelsettingduringheating
At the hot start andthe heatingthermostat OFF, regardless whether the auto swing switch is operated ornot (auto
swingorlouver stop), the louvertakes thelevelposition (in order to preventblowing ofcoolwind).The louver
positiondisplayLCDcontinuestoshowthedisplaywhichhasbeenshownbeforeenteringthiscontrol.
(iii)Louverfreestopcontrol
Ifyoutouchthe“Menu”→“Servicesetting”→“R/Csettings”→“Servicepassword”buttonsoneafteranotheron
theTOPscreenofremotecontrol,the“Flapcontrol”screenisdisplayed.Ifthefreestopisselectedonthisscreen,the
louvermotorstopsuponreceiptofthestopsignalfromtheremotecontrol.Iftheautoswingsignalisreceivedfrom
theremotecontrol,theautoswingwillstartfromthepositionbeforethestop.
(b) RC-E5
(i)Louvercontrol
1)Pressthe“LOUVER”buttontooperatetheswinglouverwhentheair-conditionerisoperating.
“SWING
”isdisplayedfor3secondsandthentheswinglouvermovesupanddowncontinuously.
2)Toxtheswinglouverataposition,pressonetimethe“LOUVER”buttonwhiletheswinglouverismovingso
that four stop positions are displayed one after another per second.
Whenadesiredstoppositionisdisplayed,pressthe“LOUVER”buttonagain.Thedisplaystops,changestoshow
the “STOP 1
”for5secondsandthentheswinglouverstops.
3)Louveroperationatthepoweronwithaunithavingthelouver4-positioncontrolfunction
Thelouverswingsonetimeautomatically(withoutoperatingtheremotecontrol)atthepoweron.
Thisallowsinputtingthelouvermotor(LM)position,whichisnecessaryforthemicrocomputerto recognizethe
louverposition.
Note(1)Ifyoupressthe“LOUVER”button,theswingmotionisdisplayedonthelouverpositionLCDfor10seconds.Thedisplaychangestothe
“SWING
” display 3 seconds later.
(ii)Automaticlouverlevelsettingduringheating
Atthehotstart with the heating thermostat OFF, regardless whether the auto swing switch is operated or not (auto
swingorlouver stop), the louver takesthe levelposition(Inorder to prevent the coldstart).The louver position
displayLCDcontinuestoshowthedisplaywhichhasbeenshownbeforeenteringthiscontrol.
(iii)Louver-freestopcontrol
Whenthelouver-freestophasbeenselectedwiththeindoorfunctionofwiredremotecontrol“
POSITION”, the
louvermotorstopswhenitreceivesthestopsignalfromtheremotecontrol.Iftheautoswingsignalisreceivedfrom
theremotecontrol,theautoswingwillstartfromthepositionwhereitwasbeforethestop.
Note (1) When the indoor function of wired remote control “ POSITION” has been switched, switch also the remote control function “
POSITION” in the same way.