EasyManua.ls Logo

Mitsubishi JT-MC206GS-W-E - User Manual

Mitsubishi JT-MC206GS-W-E
15 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
− 1 −
GB
Hand dryer
1209875HF0401
MODEL
JT-MC206GS-W-E
Unit color -W
（White）
INSTRUCTION MANUAL
■ Read the manual thoroughly before using the unit to ensure it is used safely and correctly.
After reading the manual, store it in an easily accessible location for future reference.
You should not attempt to install the unit yourself,
as this may affect the safety and functionality of the unit.
This unit is intended for the purpose of drying hands and is not covered by a warranty if used for any other purpose.
It has no sterilizing or disinfecting functions.
INDEX
Safety Precautions
2
Names of Parts
3
How to use the unit
4
■ How to open/close the front cover
4
Precautions for when opening/closing the front cover
4
■ Turning the power on
5
■ If not using for a long period
5
■ How to use the unit
5
■ Turning the heater on
6
■ Adjusting the air speed
6
Maintenance
7
Precautions for when opening/closing the front cover
7
① Turning the power off before maintenance
8
② Cleaning the unit exterior and hand drying area
8
③ Cleaning the air filter
9
④ Cleaning the drain tank
10
Trouble shooting
11
Specifi cations
12
Location of Model Name display
Location of power supply voltage display
Single-phase 220 – 240V AC
For User

Table of Contents

Questions and Answers

  • M
    Matthew GarciaAug 8, 2025
    Why does the Mitsubishi JT-MC206GS-W-E power light keep flashing?
    • M
      Maria SmithAug 9, 2025
      If the Mitsubishi hand dryer is used continually for more than 40 seconds, the power light flashes and the dryer automatically stops. Remove your hands and then re-insert them.
  • D
    Donald TaylorAug 14, 2025
    How to fix Mitsubishi JT-MC206GS-W-E Dryer when no lights in the display are on?
    • B
      Brian LopezAug 14, 2025
      First, turn the ground fault circuit interrupter on. If that doesn't work, turn the power switch to the "ON" position.
  • M
    Michael WarrenAug 18, 2025
    What to do if the Mitsubishi JT-MC206GS-W-E power light does not light up?
    • B
      Brandon FisherAug 18, 2025
      First, turn the ground fault circuit interrupter "ON" and then turn the power switch "ON". If this doesn't work, turn the power switch "OFF", ensure that all lights on the display are off, and wait 1 minute before switching the power back "ON".
  • A
    Amy GregoryAug 25, 2025
    How to turn on the heater switch on a Mitsubishi JT-MC206GS-W-E?
    • B
      Bianca GuzmanAug 25, 2025
      Open the front cover and turn the heater switch to the "ON" position.
  • J
    Justin HudsonAug 28, 2025
    What to do if no air blows from my Mitsubishi Dryer?
    • D
      daniel46Aug 28, 2025
      Place your hands all the way inside the hand drying area. Also, remove any foreign substances or dirt after turning the power switch "OFF" and waiting until the power light goes out. Then, wait at least 1 minute after turning the power switch "OFF", and then turn it back "ON" again.
  • M
    Matthew MathewsSep 2, 2025
    Why is the air cold in my Mitsubishi JT-MC206GS-W-E?
    • T
      Tiffany ReynoldsSep 2, 2025
      This Mitsubishi unit has a built-in heater, but the air may not feel warm when the room temperature is low, especially if the air conditioning is not working or the room temperature is 20°C or below.

Summary

Safety Precautions

General Safety Warnings

Key warnings about severe hazards and potential death or injury.

General Safety Cautions

Cautions about minor injuries or property damage from incorrect handling.

How to Use the Unit

Power Operation

Turning the Power On

Procedure for switching the unit's power on.

Hand Drying Operation

Functional Settings

Maintenance Procedures

Maintenance Safety Warnings

Critical safety precautions before performing maintenance.

Troubleshooting

Mitsubishi JT-MC206GS-W-E Specifications

General IconGeneral
BrandMitsubishi
ModelJT-MC206GS-W-E
CategoryDryer
LanguageEnglish