© Mit bi hi F klift T k 2013 All
© Mit bi hi F klift T k 2013 All i ht di ht d R i i BR i i B
D t ID 615023D t ID 615023
100 (244)100 (244)
PBV20N2 PBV20N2 Service Service ManualManual
CONNECTION DESCRIPTION
CONNECTION DESCRIPTION
C6 DI0 (XA1 C/6)C6 DI0 (XA1 C/6)
(tiller switch S12)(tiller switch S12)
Input of the switch DI0. The Input of the switch DI0. The input is activated wheninput is activated when
it is connected to +Batt. it is connected to +Batt. With the logic hardwareWith the logic hardware
properly configured, it can be used to properly configured, it can be used to supply the EBsupply the EB
and MC positive voltage. The default function and MC positive voltage. The default function is theis the
controller TILLER input.controller TILLER input.
C7 DI2 (XA1 C/7)C7 DI2 (XA1 C/7)
(side guard in S15 and S16)(side guard in S15 and S16)
Input of the switch DI7. The Input of the switch DI7. The input is activated wheninput is activated when
it is connected to +Batt. The default function is theit is connected to +Batt. The default function is the
controller H&S (Hard & Soft) request input. Whencontroller H&S (Hard & Soft) request input. When
this input is closed, the truck performances arethis input is closed, the truck performances are
modified.modified.
C8 PPOTC8 PPOT
(pressure sensor supply B42)(pressure sensor supply B42)
Potentiometer’s positive supply. The hardware hasPotentiometer’s positive supply. The hardware has
to be configured to the output +12 V or +5 V.to be configured to the output +12 V or +5 V.
C9 CPOTLC9 CPOTL
(pressure sensor output B42)(pressure sensor output B42)
Lift/lower potentiometer wiper input.Lift/lower potentiometer wiper input.
C10 CANL (XA1 C/10)C10 CANL (XA1 C/10)
(CAB bus green)(CAB bus green)
Low level CAN bus voltage I/O.Low level CAN bus voltage I/O.
8.2.3.4 8.2.3.4 CND CND external external connectorconnector
CONNECTION DESCRIPTION
CONNECTION DESCRIPTION
D1 ENC A (XA1 D/1)D1 ENC A (XA1 D/1)
(traction motor encoder phase A M1)(traction motor encoder phase A M1)
Traction motor encoder phase A.Traction motor encoder phase A.
D2 PENC (XA1 D/2)D2 PENC (XA1 D/2)
(traction motor encoder supply M1)(traction motor encoder supply M1)
Encoder positive supply. The hardware has to beEncoder positive supply. The hardware has to be
configured to the output +12 V or +5 V.configured to the output +12 V or +5 V.
D3 PTHERM (XA1 D/3)D3 PTHERM (XA1 D/3)
(temperature sensor R31)(temperature sensor R31)
Traction motor’s thermal sensor positive inputTraction motor’s thermal sensor positive input
5VDC. The resistance of the sensor is 5815VDC. The resistance of the sensor is 581 Ω atΩ at
2020
˚C.˚C.
D4 ENC B (XA1 D/4)D4 ENC B (XA1 D/4)
(traction motor encoder phase B M1)(traction motor encoder phase B M1)
Traction motor encoder phase B.Traction motor encoder phase B.
D5 NENC XA1 D/4)D5 NENC XA1 D/4)
(traction motor encoder gnd M1)(traction motor encoder gnd M1)
Negative of the encoder.Negative of the encoder.
D6 NTHERM (XA1 D/6)D6 NTHERM (XA1 D/6)
(temperature sensor R31)(temperature sensor R31)
Negative (GND) for the motor thermal sensor.Negative (GND) for the motor thermal sensor.
To Next Page
Loading...
