Mitsubishi PBV20N2 - Page 229

© Mitsubishi Forklift Trucks 2013. All © Mitsubishi Forklift Trucks 2013. All rights reserved.rights reserved. Revision: BRevision: B
Document ID: 615023Document ID: 615023
228 (244)228 (244)

MICRO SLAVE KOMICRO SLAVE KO
This alarm occurs if This alarm occurs if the microprocessor detects a mismatch between the commanded andthe microprocessor detects a mismatch between the commanded and
active steering directions. In such a case, replace the active steering directions. In such a case, replace the steering controller.steering controller.


PBV20N2 PBV20N2 Service Service ManualManual
CODE
CODE TRUCKTOOL TRUCKTOOL AND AND DISPLAY DISPLAY DESCRIPTIONDESCRIPTION
247247 CAN-BUS communication errorCAN-BUS communication error
CAN BUS KOCAN BUS KO
(Warning)(Warning)
This warning occurs if the steering controller does not This warning occurs if the steering controller does not receive a message from the tractionreceive a message from the traction
controller within one second. In such a controller within one second. In such a case, check the CAN bus wiring from the COMBIACXcase, check the CAN bus wiring from the COMBIACX
controller to the steering controller.controller to the steering controller.
248248 Steering sensor out of rangeSteering sensor out of range
S.P. OUT OF RANGES.P. OUT OF RANGE
(Alarm)(Alarm)
StoredStored
This alarm occurs if the command HALL sensor (or potentiometer) signal voltage is out This alarm occurs if the command HALL sensor (or potentiometer) signal voltage is out ofof
range (from 0.8 Vdc to range (from 0.8 Vdc to 4.2 Vdc). In such a case, check that the 4.2 Vdc). In such a case, check that the connectors and cables are inconnectors and cables are in
order and measure that the command sensor signal voltage is order and measure that the command sensor signal voltage is within tolerance.within tolerance.
249249
Feedback sensor out of rangeFeedback sensor out of range
F.FB: OUT OF RANGEF.FB: OUT OF RANGE
(Alarm)(Alarm)
StoredStored
This alarm occurs if the feedback HALL sensor (or potentiometer) signal voltage is This alarm occurs if the feedback HALL sensor (or potentiometer) signal voltage is out of rangeout of range
(from 0.3 Vdc to 4.7 (from 0.3 Vdc to 4.7 Vdc). In such a case, check that the Vdc). In such a case, check that the connectors and cables are in orderconnectors and cables are in order
and measure that the feedback sensor signal voltage is and measure that the feedback sensor signal voltage is within tolerance.within tolerance.
250250 Internal microprocessor errorInternal microprocessor error
MICRO SLAVEMICRO SLAVE
(Alarm)(Alarm)
StoredStored
This alarm occurs when the internal microprocessor information does not match. In such aThis alarm occurs when the internal microprocessor information does not match. In such a
case, replace the steering controller.case, replace the steering controller.
251251 Internal safety contact is openInternal safety contact is open
KM OPENKM OPEN
(Alarm)(Alarm)
StoredStored
This alarm occurs when the microprocessor detects that the internal safety contact is openThis alarm occurs when the microprocessor detects that the internal safety contact is open
when it is expected to when it is expected to be closed. In such a case, replace the be closed. In such a case, replace the steering controller.steering controller.
252252
Internal safety contact 2 is openInternal safety contact 2 is open
KS OPENKS OPEN
(Alarm)(Alarm)
StoredStored
This alarm occurs when the microprocessor detects that the second internal safety contact isThis alarm occurs when the microprocessor detects that the second internal safety contact is
open when it is open when it is expected to be closed. In such a expected to be closed. In such a case, replace the steering controller.case, replace the steering controller.
253253 Internal safety contact is closedInternal safety contact is closed
KM CLOSEDKM CLOSED
(Alarm)(Alarm)
StoredStored
This alarm occurs when the microprocessor detects that the internal safety contact is closedThis alarm occurs when the microprocessor detects that the internal safety contact is closed
when it is expected to be open. In such a case, replace the steering controller.when it is expected to be open. In such a case, replace the steering controller.
254254 Internal safety contact 2 is closedInternal safety contact 2 is closed
KS CLOSEDKS CLOSED
(Alarm)(Alarm)
StoredStored
This alarm occurs when the microprocessor detects that the second internal safety contact isThis alarm occurs when the microprocessor detects that the second internal safety contact is
closed when it is expected to closed when it is expected to be open. In such a be open. In such a case, replace the steering controller.case, replace the steering controller.
https://www.forkliftpdfmanuals.com/