Mitsubishi QD51 - Page 12

A - 11 A - 11
ZBAS
(
Returns the number of the BASIC task area in which the program currently being created
)
.....11-405
ZCLOSE
(
Closes a communication channel
)
...........................................................................................11-406
ZCNTL 11-407
ZCNTL - Processing Code 16 - (Specifying communication parameter).................................................11-409
ZCNTL - Processing Code 17 - (Reading communication parameters) ..................................................11-409
ZCNTL - Processing Code 18 - (Specifying communication control parameters)...................................11-411
ZCNTL - Processing Code 19 - (Reading communication control parameters)......................................11-411
ZCNTL - Processing Code 22 - (Specifying break characters) ................................................................11-414
ZCNTL - Processing Code 23 - (Reading break characters) ...................................................................11-414
ZCNTL - Processing Code 24 - (Specifying continuous break characters) .............................................11-416
ZCNTL - Processing Code 25 - (Reading continuous break characters) ................................................11-416
ZCNTL - Processing Code 32 - (Turning ON/OFF the RS and ER control signals)................................11-418
ZCNTL - Processing Code 33 - (Reading the ON/OFF status of the CS, DR, RS, ER and CD
control signals)........................................................................................................................11-420
ZCNTL - Processing Code 48 - (Specifying high impedance control) .....................................................11-422
ZCNTL - Processing Code 64 - (Reading causes of reception errors) ....................................................11-423
ZCNTL - Processing Code 80 - (Reading the receive buffer size and the number of characters) .........11-425
ZCNTL - Processing Code 96 - (Specifying Kanji code conversion)........................................................11-426
ZCNTL - Processing Code 100 - (Specifying Kanji shift in/out codes).....................................................11-427
ZCNTL - Processing Code 128 - (Reading the printer status) .................................................................11-430
ZCNTL - Processing Code 136 - (Outputting the initialization signal to the printer)................................11-432
ZEVENT
(
Enables or disables event generation
)
.....................................................................................11-433
ZIDV
(
Specifies the data input device for the INPUT instruction, etc
)
.....................................................11-434
ZLDV
(
Selects a communication port for a printer
)
...................................................................................11-435
ZMESSAGE
(
Defines a message port
)
.....................................................................................................11-436
ZMESSAGE CLOSE
(
Closes message ports
)
..........................................................................................11-439
ZMESSAGE GET
(
Reads messages from message ports
)
.....................................................................11-440
ZMESSAGE KILL
(
Deletes the message ports
)
.......................................................................................11-442
ZMESSAGE OPEN
(
Opens a message port
)
...........................................................................................11-443
ZMESSAGE PUT
(
Writes messages to a message port
)
........................................................................11-444
ZMOVE
(
Transfers data between valiables
)
.............................................................................................11-446
ZODV
(
Specifies the data output destination for the PRINT instruction, etc
)
..........................................11-451
ZOPEN
(
Opens a communication channel
)
..............................................................................................11-452
ZRECEIVE
(
Receives data from a communication channel
)
...................................................................11-454
ZRELEASE
(
Allows other programs to use a resource to which a resource number is assigned
)
........11-460
ZRESERVE
(
Prohibits other programs from using a resource to which a resource number is
assigned
)
................................................................................................................................11-461
ZSEND
(
Sends data from a communication channel
)
..............................................................................11-463
ZSIGNAL
(
Generates the specified event
)
................................................................................................11-469
ZSTART
(
Starts up the specified program
)
...............................................................................................11-470
ZURGENCY
(
Changes the priority of a program
)
.....................................................................................11-472
ZWAIT DELAY
(
Pauses the program execution until the specified time has elapsed
)
...........................11-473
ZWAIT EVENT
(
Pauses the program execution until the specified event is generated
)
........................11-474