Mitutoyo U-WAVE Series - Page 7

6) Press the DATA switch on the U-WAVE-T with the measuring tool in counting state.
Whether data transmission has been properly performed to the U-WAVE-R can be confirmed
by the LED (buzzer) of the U-WAVE-T. The LED (buzzer) status implies as follows.
Information LED Buzz (only with buzzer type)
Wireless transmission
completed properly
Green LED blinks Buzzes shortly twice
･Wireless transmission failed.
･Error occurred.
Red LED blinks. Buzzes long once.
CAUTION
・ Log in to Windows by 'Power Users' or above.
・ The green LED blinks on the U-WAVE-T if communication has been made properly
with the U-WAVE-R on which the green LED stays on even without having booted the
U-WAVEPAK.
Now, information registration is complete, allowing wireless communication to be performed.
4. Measurement Data Input Into Microsoft Excel
Proceed to input the measurement data into Excel from a measuring tool.
1)
2)
3)
4) Boot Microsoft Excel.
5) Measurement data input takes place as shown below at the press of the DATA switch.
6) To exit, click “U-WAVEPAK Data I/F” after saving the measured data.
7)
8）
CAUTION
The U-WAVEPAK automatically transmits the measurement data to the active
application software (such as Microsoft Excel or Microsoft Word). Before booting
multiple application software simultaneously, be sure to activate Microsoft Excel.
5. Inputting Measurement Data into the Specified Cell of Microsoft Excel
Measurement data input into the specified cell is possible by using the data collection
macro appended to the U-WAVEPAK. Here is how to input measurement data into the
specified cells from two units of U-WAVE-T using this macro.
1) Firstly, register the two units of U-WAVE-T in the U-WAVE-R referring to section 3.3.
2) Press the [Exit setup] button.
3) Press the [Exit] button in the U-WAVEPAK menu dialog to exit the U-WAVPAK.
4) Boot [Data Collection Macro for U-WAVE] from Windows programs menu.
5) Press [Data File] and select [Data Input].
6) “NEWUW.RPX” will open. Press [Data Input] and select [Edit].
7) Specify in the “Edit Mode” the cell into which data input is made for each channel of the U-WAVE-T.
Here, edit a table which allows measurement data to be input as shown below.
8) Press [Data Input] and select [Edit Sheet]-[Delete Input Area Size].
9)
10) Press [Data Input] and select [Data Collection Configuration].
Measurement
item 1
Measurement
item 2
Measurement
item 3
Measurement
item 4
Measurement
item 5
Measurement
item 6
Work-1
Work-2
Work-3
Work-4
Work-5
Work-6
”U-WAVEPAK Data I/F” contained in Windows task
bar will boot.
Click “U-WAVEPAK Data I/F” to display the “Data
I/F” dialog.
Press the [Exit setup] button.
Press the [Data I/F start] button.
b) Press the [OK] button.
a) Enter the column/row number to be deleted.
Here, the measurement data is indicated as
“DT1 00 00 +0000010.000M”.
Group ID Measured data
Channel
a) Press the “Stop data I/F” button.
b) Press the “Exit data I/F” button.
Press the [Exit] button to exit the U-WAVEPAK.
The “Measure mode” and “Edit
mode” are in the measurement
data input screen.
The mode selected is identified
here.
Items 7 and 8 and Work-7 and -8
will be deleted from measurement
items and work labels, respectively.
The following editing is possible
in the “Edit Mode”.
・Comments editing
・Nominal data editing
・Upper/lower tolerance value
editing
U-WAVE-T Setup
No. Channel Group ID Device ID
Measuring tool A 1 00 0000000001
Measuring tool B 2 01
00
0000000002
Measuring tool B
(Channel 01)
Measuring tool A
(Channel 00)