Controls and Connection
Status LED
The LED flashes messages that
let the user know the current
status of the Bluetooth Dongle
Radio Connector
Plugs into the 2-way
radio’s Mic/Speaker jack.
Belt Clip Version
Multifunction Talk Switch
Used to place the Bluetooth
Dongle in pairing mode.
Once paired with an audio
accessory, this switch is used
to activate the Push-To-Talk
function of the 2-way radio
Velcro Fastener
or Belt Clip
Used to attach
the Bluetooth
dongle to the
2-way radio
or to the user’s
belt or lapel
There is a clothing clip on
the back of the long cord
versions.
Velcro Fastener
Version
Charging the Bluetooth Dongle
STEP ONE: Charging the Bluetooth Dongle
The Bluetooth Dongle has an internal Lithium Ion rechargeable battery pack which must be charged prior to operation, and must be
recharged regularly. A fully charged battery will provide approximately 10 hours (or more) of operation before needing to be recharged,
however, operating time can vary depending on usage and the condition of the battery pack. Recharge the battery regularly.
To charge the Bluetooth Dongle:
1. Ensure the Bluetooth Dongle is turned off, using the switch located on the back of the device.
2. Plug the supplied wall charger into a standard 120 volt AC outlet.
3. Plug the charger into the charge jack on the bottom of the Bluetooth Dongle. You will need to remove the protective rubber cover that is
inserted into the charge jack. (To prevent dust and moisture from damaging your dongle, always ensure this cover is in place when you are
not charging the dongle.)
4. Once the charging process has begun, the LED indicator on the top of the Bluetooth Dongle will show a constant blue light. Typical
charge time is approximately 5-6 hours. Actual charge time will vary depending on several factors including the battery’s charge state,
condition, and age.
6. Disconnect the charger from the dongle when charging is completed.
Charging Cautions:
- Use only the wall charger supplied by the manufacturer. Do not use any other charger.
- Do not use a wall charger that appears to be damaged. (Example: frayed wires, melted plastic, etc.)
Contact your dealer to get a new manufacturer-approved replacement
charger. - Do not tamper with or modify the Bluetooth Dongle or charger.
-Always turn the power switch to the off position when charging the Bluetooth Dongle.
QUICK START
1. Connect the Bluetooth dongle to a compatible 2-way radio.
2. Pair the Bluetooth dongle with a compatible wireless audio accessory.
3. Test and use.
2
Connecting the Dongle to Radio
STEP TWO: Connecting to a 2-way Radio
To connect your Bluetooth Dongle to a 2-way radio, follow these steps:
* Always turn off your 2-way radio before connecting the Bluetooth Dongle.
* Plug the Bluetooth dongle’s radio connector into the speaker-microphone / audio accessory jack of your 2-way radio. *
You can attach the Bluetooth Dongle to your 2-way radio or clothing using the Velcro fastener.
3 4
This manual applies to all
Blueooth dongle for
radios with SINGLE or
DUAL PIN accessory
connectors
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting antenna
headset or other audio accessory with
your 2-way radio.
For Portable Radios with SIMPLE PIN accessory
connector
Mobility Sound Technology Ltd.
5F, No.100, Jian 1
st
Road, ZhongHe Dist.
New Taipei City 23585, Taiwan
Tel: (886) 2 2223-2377 Fax: (886) 2 2223-1968
To Next Page
Need help?
General