Modal SKULPTsynth SE - Page 20

38 39
MIDI CC Implemention Chart
Function CC Values
Osc2 Fine Detune 31 -/+ 1 Semitone
FEG Amount 32 63 (0) +/- 63
Morph 33 0 = LP / 64 = BP / 127 = HP
Cutoff 34 0Hz - 22kHz
Reso 35 None - Full
LFO1 Rate 36
NO SYNC: 0-127 = 0.02Hz - 32Hz
SYNC: 0-7 = 1/16 / 8-15 = 1/8 / 16-23 = 3/16 / 24-31 = 1/4 /
32-39 = 3/8 / 40-47 = 1/2 / 48-55 = 3/4 / 56-63 = 1 / 64-71 = 3/2
/ 72-79 = 2 / 80-87 = 3 / 88-95 = 4 / 96-103 = 6 /104-111 = 8 /
112-119 = 12 / 120-127 = 16
LFO1 Depth 37 63 (0) +/- 63
LFO1 Shape 39
0-32 Sine to Triangle / 33-64 - Triangle to Sawtooth / 65-96 -
Sawtooth to Square / 97-127 - Square to Sample and Hold
Octave 40 Octaves -2 to +4
MEG Attack 43 0 - 4 Seconds
MEG Decay 44 0 - 4 Seconds
MEG Sustain 45 0 - 1
MEG Release 46 0 - 4 Seconds
LFO2 Rate 47
NO SYNC: 0-63 = 0-32Hz Free / 64-71 Root/8 / 72-79 Root/4 /
80-87 Root/2 / 88-95 Root / 96-103 Root*1.5 /104-111 Root*2 /
112-119 Root*2.5 / 120-127 Root*3
SYNC: 0-7 = 1/16 / 8-15 = 1/8 / 16-23 =1/4 / 24-31 =1/2 / 32-39
= 1 / 40-47 = 5/4 / 48-55 =2 / 56-63 = 4 (Cycles per beat)
LFO2 Depth 48 63 (0) +/- 63
MEG Amount 49 63 (0) +/- 63
LFO2 Shape 50
0-32 Sine to Triangle / 33-64 - Triangle to Sawtooth / 65-96 -
Sawtooth to Square / 97-127 - Square to Sample and Hold
AEG Amount 51 63 (0) +/- 63
LFO1 MIDI Sync 52 0 - 63 = OFF / 64 - 127 = ON
Ring Mod 53 0 - 63 = OFF / 64 - 127 = ON
LFO2 MIDI Sync 54 0 - 63 = OFF / 64 - 127 = ON
Delay MIDI Sync 55 0 - 63 = OFF / 64 - 127 = ON
MIDI CC Implemention Chart
Function CC Values
LFO1 Mode 56 0-41 Retrig / 42-83 Free / 84-127 Single
LFO2 Mode 57 0-41 Retrig / 42-83 Free / 84-127 Single
Arp Status 58 0 - 63 = OFF / 64 - 127 = ON
Arp Octave 59 0 - 31 1Oct / 32-63 2Oct / 64-95 3Oct / 96-127 4Octaves
Arp Direction 60
0-20 = Forwards, 21-41 = Backwards, 42-62 = Pendulum, 63 - 83
= Note Forwards, 84 - 104 = Note Backwards, 105-127 = Note
Pendulum
Arp Division 61
Value / 16 = 1/32nd, 1/24th, 1/16th, 1/12th, 1/8th, 1/6th, 1/4th,
1/2nd
Velo Depth 62 63 (0) +/- 63
Note Depth 63 63 (0) +/- 63
Sustain Pedal 64 0 - 63 = OFF / 64 - 127 = ON
Aftertouch Depth 65 63 (0) +/- 63
Ext Depth 66 63 (0) +/- 63
Sequence Length 67 0 - 31 = 1 Bar / 32-63 = 2 Bars / 64-95 = 4 Bars / 96-127 = 8 Bars
Sequence Hold 70 0 - 63 = OFF / 64 - 127 = ON
Sequence Loop 71
To Skulpt: 127 sets loop start point, 0 sets loop stop point. From
Skulpt: 127 is currently looping, 0 is not looping
Transpose 75 -24 to +36 sent as (value + 24) * 2
Swing 78 0 - 127
Anim 1 CC 80 CC number of new destination
Anim 2 CC 81 CC number of new destination
Anim 3 CC 82 CC number of new destination
Anim 4 CC 83 CC number of new destination
All Envelope Attack 84 0 - 4 Seconds
All Envelope Decay 85 0 - 4 Seconds
All Envelope Sustain 86 0 - 1
All Envelope Release 87 0 - 4 Seconds