Moen 6410 SERIES User Manual

Lift
Rod
3/4”
(19mm)
Max. Deck
Thickness
Cold
1/2" NPT
Hot
1/2" NPT
4“
(102mm)
4-1/4“
(108mm)
4“
(102mm)
3“
(76mm)
3-7/8“
(98mm)
6-3/16“
(157mm)
DESCRIPTION
• Metal construction with various finishes identified by suffix
• 1/2" IPS connections
• Includes metal pop-up waste assembly
OPERATION
• Lever style handles
• Maximum handle(s) rotation angle is 90˚ to full on
• Rotate hot side counterclockwise to open (clockwise to close)
• Rotate cold side clockwise to open (counterclockwise to close)
FLOW
• Flow is limited to 1.5 gpm max (5.7L/min) at 60 psi,
for products made before October 2008 flow is limited to
2.2 gpm max (8.3 L/min)
CARTRIDGE
• 1224 cartridge design
• Nonmetallic and stainless steel material
STANDARDS
• Third party certified to WaterSense,® CSA B125.1, ASME A112.18.1,
ANSI A117.1, and all applicable requirements referenced therein
• Certified to ANSI/NSF 61/9
• Contains no more than 0.25% weighted average lead content
• Complies with California Proposition 65 and with the Federal Safe
Drinking Water Act
• ADA for lever handles
WARRANTY
• Lifetime limited warranty against leaks, drips and finish defects
to the original consumer purchaser
• 5 year warranty if used in commercial installations
EVA™
4" Lavatory Faucet
with Metal Waste Assembly
Models: 6410 series
Bulk Models: 66410, 66411*
(Bulk packed 6 per carton),
50/50 waste assembly
*Includes hot (red) and cold (blue) indicators.
NOTE: THIS FAUCET IS DESIGNED TO BE
IN STALLED THRU 3 HOLES, 1" MIN. DIA.
CRITICAL DIMENSIONS
(DO NOT SCALE)
Spec i fi ca tions
FOR MORE INFORMATION CALL: 1-800-BUY-MOEN
www.moen.com
Rev. 3/11

Moen 6410 SERIES Specifications

General

Model	6410 SERIES
Finish	Chrome
Mounting Type	Deck Mount
WaterSense Certified	Yes
Handle Type	Lever
Number of Handles	2
Connection Size	1/2 inch
Connection Type	Compression
ADA Compliant	Yes
Installation Type	3-hole
Valve Type	Ceramic Disc
Warranty	Limited Lifetime
Flow Rate	1.2 GPM
Spout Reach	4 15/16"

Summary

Product Description and Features

Metal Construction & Connections

Features metal construction, 1/2" IPS connections, and metal pop-up waste assembly.

Operation Details

Describes lever handle operation, 90° rotation angle, and hot/cold side control.

Flow Rate Specifications

Specifies flow limit of 1.5 gpm at 60 psi, with older models limited to 2.2 gpm.

Cartridge Information

Details the 1224 cartridge design and its nonmetallic/stainless steel material.

Certifications and Standards

Lists certifications like WaterSense, CSA, ASME, ANSI, and compliance with lead content and safety acts.

ADA Compliance

Confirms ADA compliance specifically for the lever handles.

Warranty Information

Outlines lifetime limited warranty for leaks/drips/finish and 5-year for commercial use.

Product Identification and Dimensions

Model Series and Type

Identifies the faucet as EVA™ 4" Lavatory Faucet with Metal Waste Assembly, Model 6410 series.

Installation Requirements

Notes that the faucet is designed for 3-hole installation with a 1" minimum diameter.

Critical Dimensions Diagram

Provides a diagram showing key measurements for installation and clearance.