Mondella Concerto FHS101 - User Manual

CONCERTO HEATED BIDET SUITE
PACKAGE CONTENTS
CARTON 2
Rimless Pan
Vario Bend
S Trap
Cistern
Flush Valve
Fill Valve
Inlet Plug
Heated Bidet Seat
(& Parts)
Cistern
Outlet Seal
Pan/Cistern
Bolts
Smart Seat
Instruction Manual
Floor Fixing
Brackets
Instruction
Manual
Plumber’s Installation Guide
This toilet suite must be installed by a
licensed plumber in accordance with local,
State and National Standards and
Regulations.
Before Installation
The Concerto Heated Bidet Suite requires the
following setout for bottom entry installation as well as external
connection requirements for water and power supply for the
Heated Bidet Seat.
Setout 90-180mm setout for S trap and 180mm for P trap.
This toilet is supplied with a vario bend S trap. Please note, a
suitable P trap connection can be installed when required. Floor
and wall must be perpendicular and the toilet must be installed
on a level surface.
Smart Seat Plumbing The Concerto Heated Bidet Seat
requires water supply on the left of the toilet so that a T valve
and hose may be installed as part of the smart seat installation
(see figure on right).
Smart Seat Power Supply The Concerto Heated Bidet
Seat requires a power outlet to the right of the toilet that must be
installed as per local, State and National regulations.
Please note:
Product measurements are subject to
some variance due to manufacturing process.
Always check physical product dimensions
prior to setout and installation.
Installation Guide
1. Install the floor fixing kit, excluding the external screws:
a) Place pan into position, tracing around the outside
of the pan and marking floor alongside the two holes
on either side of the pan.
b) Remove pan and mark points for bracket installation
on inside of pan floor area and in line with pan holes
from 1(a), allowing clearance for pan thickness (see
Fig.2).
c) Drill holes into floor to required depth and apply wet
area silicone into the holes and to base of floor
bracket. Install the floor bracket using floor plugs,
washers and screws supplied (Fig.3). Do not install
external screws until Step 10.
2. Into the 2 holes in the top rear of the pan, install the pan
spigots, washers and nuts (Fig.4) with the cistern to be
attached in Step 7. Feed a flexible hose (not supplied)
through bottom entry hole of pan and then continue to
feed the hose out through the top of the pan.
3. For S trap installation, position the vario bend S Trap and
determine whether trimming is required to meet pan outlet
and waste connections (Fig 5). If trimming is required,
measure the vario bend carefully, mark and then cut
accordingly. Anchor vario bend to wall by measuring,
marking, drilling and fixing (Fig.6).
4. Replace vario bend cover and install, ensuring that the
connection points are secured correctly with a complete
seal.
5. Install the Cistern Outlet Seal to base of cistern, over the
outlet flush pipe (Fig.7).
6. Attach the flexible hose (from step 2) to the inlet valve
connection on bottom of cistern. Please note the inlet
valve position can be changed between right side and
left side with the unused inlet valve to be sealed with the
Inlet Plug supplied.
7. Using the Pan/Cistern Bolts provided, connect the cistern
and pan together (Fig.8). If necessary, the outlet flush
valve may be temporarily removed to make it more
accessible to fix the pan and cistern bolts into place.
Ensure the outlet flush valve is placed back into position.
8. Install flush button to cistern cover, adjusting toggles if
needed (Fig.9).
9. Before fixing external screws into side of toilet, connect
water supply and conduct several flush tests and ensure
that there are no leaks.
10. Install external screws to fixing brackets within pan
(Fig.10) and cover with white caps provided (Fig.11).
11. Complete installation of pan and cistern by sealing
around base of toilet with a bead of wet area silicone
and allow to dry before use (Fig.12).
12. For installation of Concerto Heated Bidet Seat, follow
installation instructions (supplied separately).
360
360
305
375
Hose from
water
supply to
smart
seat
Power cord
to power supply
395
180
235
700
610
700
8
1
0
700
4
0
5
4
1
5
2
4
5
Ø32
3
0
Ø10
280
1
5
85
Dual Flush
Button
CARTON 1
Dimensions in mm
1
Please ensure that all items below have been included in this Concerto Heated Bidet Suite and that all parts are
undamaged prior to installation. If any items are damaged or missing, please contact Customer Support immediately.

Summary

Package Contents

Before Installation

Smart Seat Plumbing Requirements

Requires water supply on the left of the toilet for T valve and hose installation.

Smart Seat Power Supply Requirements

Requires power outlet to the right of the toilet, installed per local regulations.

Installation Steps

Floor Fixing Kit Installation

Instructions for placing the pan, marking, drilling, and installing the floor bracket.

Pan Spigots and Hose Connection

Connecting pan spigots and feeding a flexible hose through the bottom entry hole.

Vario Bend S Trap Installation

Positioning, trimming if necessary, and anchoring the vario bend S trap.

Cistern Outlet Seal and Inlet Valve Hose

Installing the outlet seal and connecting the flexible hose to the inlet valve.

Cistern and Pan Assembly

Connecting the cistern and pan using provided bolts, ensuring proper seating.

Flush Button and Final Fixing

Installing the flush button and securing external screws with white caps.

Water Supply, Leak Test, and Sealing

Connecting water supply, performing flush tests, and sealing the toilet base.

Overview

1. Function Description
2. Important Technical Specifications
3. Dimensions (in mm)
4. Components Included in Carton 1
5. Components Included in Carton 2
6. Plumbing Requirements
7. Electrical Requirements
8. Usage Features
9. Rimless Pan
10. Dual Flush System
11. Heated Bidet Seat (Smart Seat)
12. Vario Bend S-Trap
13. Maintenance Features
14. Easy Cleaning
15. Component Replacement
16. Installation Considerations for Maintenance
17. General Maintenance Advice
18. Installation Process (Summary)

The Mondella Concerto Heated Bidet Suite is a comprehensive toilet system designed for comfort and hygiene, featuring a heated bidet seat and a rimless pan. This suite requires professional installation by a licensed plumber in accordance with local, State, and National Standards and Regulations.

Function Description:

The Mondella Concerto Heated Bidet Suite integrates a standard toilet with a heated bidet seat, offering enhanced hygiene and comfort. The system includes a rimless pan for easier cleaning, a dual-flush cistern for water efficiency, and a smart bidet seat with heating capabilities. The bidet seat requires both a water supply and a power outlet for its operation, providing warm water washing functions. The rimless design of the pan prevents dirt and grime build-up, contributing to a more hygienic toilet. The dual-flush mechanism allows users to choose between a full or half flush, optimizing water usage.

Important Technical Specifications:

Dimensions (in mm):

• Overall Height: 810 mm
• Pan Height: 415 mm
• Pan Depth (front to back): 700 mm
• Pan Width: 360 mm
• Cistern Width: 375 mm
• Cistern Depth: 170 mm (approx. based on diagram)
• Setout for S-trap: 90-180 mm
• Setout for P-trap: 180 mm
• Floor Fixing Bracket Dimensions: 280 mm (length) x 80 mm (width)
• Inlet Valve Position: Can be changed between right and left side.
• Water Supply Connection: On the left side of the toilet for the smart seat.
• Power Outlet Connection: On the right side of the toilet for the smart seat.

Components Included in Carton 1:

• Rimless Pan
• Vario Bend S-Trap (for 90-180mm setout)
• Floor Fixing Brackets
• Instruction Manual

Components Included in Carton 2:

• Cistern
• Fill Valve
• Flush Valve
• Dual Flush Button
• Inlet Plug
• Cistern Outlet Seal
• Pan/Cistern Bolts
• Heated Bidet Seat (& Parts)
• Smart Seat Instruction Manual

Plumbing Requirements:

• Water Supply: The smart seat requires a water supply connection on the left side of the toilet. A T-valve and hose are used for this connection.
• Trap Setout: The suite is supplied with a vario bend S-trap suitable for 90-180mm setout. A P-trap connection can be installed if required.
• Inlet Valve: The inlet valve position can be adjusted between the right and left sides of the cistern. The unused inlet is sealed with the provided inlet plug.

Electrical Requirements:

• Power Outlet: The heated bidet seat requires a power outlet to be installed on the right side of the toilet, compliant with local, State, and National regulations.

Usage Features:

Rimless Pan:

• Hygiene: The rimless design eliminates hidden ledges where dirt and germs can accumulate, making the pan easier to clean and more hygienic.
• Flushing Efficiency: The direct flush ensures water covers the entire bowl effectively, providing a powerful and efficient rinse.

Dual Flush System:

• Water Conservation: The dual flush button allows users to select between a full flush for solid waste and a half flush for liquid waste, contributing to water savings.

Heated Bidet Seat (Smart Seat):

• Comfort: The seat provides heating functionality for enhanced user comfort, especially in colder environments.
• Hygiene: Offers a warm water washing function for improved personal hygiene.
• Controls: The bidet seat comes with its own instruction manual for detailed operation and feature descriptions.

Vario Bend S-Trap:

• Flexibility: The vario bend S-trap allows for adjustable setout distances (90-180mm), accommodating various plumbing configurations.

Maintenance Features:

Easy Cleaning:

• Rimless Pan: The absence of a traditional rim simplifies cleaning, as there are no hidden areas for grime to build up. This reduces the effort and time required for toilet maintenance.
• Smooth Surfaces: The overall design with smooth ceramic surfaces facilitates easy wiping and cleaning.

Component Replacement:

• Modular Design: Components like the fill valve, flush valve, and bidet seat are separate units, allowing for easier replacement or servicing if needed.
• Cistern Outlet Seal: The cistern outlet seal is designed for a secure fit, preventing leaks and ensuring long-term performance.

Installation Considerations for Maintenance:

• Access: The design allows for access to internal components for maintenance, such as the cistern's fill and flush valves.
• Water and Power Connections: The separate water and power connections for the bidet seat mean that its maintenance can be performed independently of the main toilet structure.

General Maintenance Advice:

• Regular Cleaning: Regular cleaning of the pan and seat with appropriate toilet cleaners is recommended to maintain hygiene and appearance.
• Seal Checks: Periodically check seals (e.g., cistern outlet seal, pan-to-floor seal) for any signs of wear or leakage to prevent water damage.
• Professional Servicing: For complex issues or repairs, especially concerning the bidet seat's electrical and water components, professional servicing is advised.

Installation Process (Summary):

1. Floor Fixing Kit Installation: Mark and drill holes for floor brackets, apply silicone, and install brackets.
2. Pan Spigots: Install pan spigots, washers, and nuts into the pan. Feed a flexible hose through the pan.
3. S-Trap Installation: Position and trim the vario bend S-trap if necessary, then anchor it to the wall.
4. Vario Bend Cover: Install the vario bend cover, ensuring secure connections.
5. Cistern Outlet Seal: Install the cistern outlet seal to the base of the cistern.
6. Flexible Hose Connection: Attach the flexible hose to the cistern's inlet valve.
7. Cistern and Pan Connection: Connect the cistern and pan using the provided bolts.
8. Flush Button Installation: Install the flush button to the cistern cover.
9. Water Supply & Flush Tests: Connect water supply and perform flush tests to check for leaks before final fixing.
10. External Screws: Install external screws to fixing brackets and cover with caps.
11. Sealing: Seal around the base of the toilet with wet area silicone.
12. Bidet Seat Installation: Follow separate instructions for the Concerto Heated Bidet Seat.

Mondella Concerto FHS101 Specifications

General

Brand	Mondella
Model	Concerto FHS101
Category	Toilets
Language	English