EasyManua.ls Logo

Moni NITRO - Intended Use; Legal Requirements

Moni NITRO
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
18
The restraint system complies with the requirement of Ordinance 44 of the Economic committee of Europe of the Organization
of United Nations (UN/ECE Regulation No.16).
NOTICE
ГРУПА 0+ (0-13 kg), ГРУПА I (9-18 kg), ГРУПА II (15-25 kg), ГРУПА III (22-36 kg)
1. This is a “UNIVERSAL” CHILD RESTRAINT SYSTEM. It is approved to Regulation No. 44, 04 series amendments,
for general use in vehicles and it will fit most, but not all car seats.
2. A correct fir is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehicle is capable
of accepting a “Universal” child restraint for this age group.
3. This child restraint has been classified as Universal under more stringent conditions than those which
applied to earlier designs which do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.
This product is a universal restraint system for children approved under standard ECE R44/04 for weight group 0+,1,2,3
for children weighing from 0 to 36 kg. For weight group 0+ the car seat must be placed in the direction opposite to
the direction of movement of the car and the child must be facing the rear seat. For weight groups 1,2,3 the car seat
must be places in the direction of movement of vehicle and the child faces the traffic.
The child restraint system NITRO I-Size is approved:
for children from 0 kg to 13 kg weight (GROUP 0+): the car seat is installed in rear-facing mode, with a 5-
point safety harness, top tether and ISOFIX connectors attached to the ISOFIX anchorage points OR with 5-
point safety harness and a 3-point seat belt.
for children from 9 kg to 18 kg weight (GROUP I): the car seat is installed in a forward-facing mode, with a
5-point safety harness, top tether and ISOFIX connectors attached to the ISOFIX anchorage points OR with a
5-point safety harness and a 3-point seat belt.
for children from 15 kg to 36 kg weight (GROUP II and III): the car seat is installed in a forward-facing mode,
with a 3-point seat belt and ISOFIX connectors fixed to the ISOFIX anchorage points OR with a 3-point seat belt
only.
ATTENTION: Never install the car seat in the direction of vehicle traffic and the child in the “FORWARD FACING
position before the child is 15 months old.
ATTENTION: Do not use top-tether when the child’s size range reaches 100-150 cm.
THIS RESTRAINT SYSTEM IS SUITABLE ONLY IF THE APPROVED VEHICLES ARE EQUIPPED WITH LAP/3-POINT/ STATIC
WITH RETRACTING SAFETY BELTS, APPROVED TO UN/ECE REGULATION NO. 16 OR OTHER EQUIVALENT STANDARDS.
Check in the instructions of your car if this universal restraint system for children from the mentioned size range can
be placed.
The child safety car seat has been manufactured, tested and certified in accordance with the requirements of the
European Standard for Child Safety Equipment (ECE R 44/04). The seal with the E approval mark (in a circle) and the
approval number are on the approval label (sticker affixed to the child seat). This approval will be invalid if you make
any changes to the child safety seat. Only the manufacturer is allowed to make changes to the child restraint system.
Car safety belts: diagonal belt; lap belt; ISOFIX attachements.
Instruction on the ISOFIX child restraint system (in Group 0+,1):
This is the ISOFIX child restraint system. It has been approved under Regulation No 44, the 04 series of amendments,
for general use in vehicles equipped with an ISOFIX anchorage system. Vehicles with positions approved as ISOFIX
positions (as described in the vehicle manual) must be fitted, depending on the child seat category and the device.
The mass group and size class ISOFIX for which this device is intended are: ISOFIX size E class for group (0-10 kg)
and ISOFIX size D for group 1 (9-18kg). Check the car manufacturer’s handbook.
EN
INTENDED USE
TYPES OF APPROVAL BELTS TO HAVE IN THE VEHICLE FIGURE B
LEGAL REQUIREMENTS

Related product manuals